Friedrich UCT08A10A, Руководство по обслуживанию и запасным частям

Страница: 12 / 74

12 PB
OPERATION
Remote Control
Figure 301 (Remote Control Operation)
1
2
3
3
4
5
6 7
8
9
1. Power:
Turn the air conditioner on and off. This button will clear the TIMER
setting.
2. MODE: Press the button to select the mode of operation, AUTO, COOL, DRY, FAN ONLY,
HEAT.
Note: The HEAT mode is only for some heating models. If you do not need it, press the
MODE button for more than 5 seconds to delete the HEAT function, and the COOL mode will
be selected automatically. Press the MODE again for more than 5 seconds to add the HEAT
function, and the HEAT mode will be selected automatically.
3. + And -
: Use these buttons to increase or decrease the setting Temperature or
Timer. Setting temperature range: 61 ~88°F (Ё) or 16 ~31°C (Ё).
Note:
When the remote controller is turned off, press and buttons can pre-set the
temperature. After the setting, the remote temperature display will be off after a
while.
4. TURBO:
When the remote is ON, press the button to active the TURBO function,
under AUTO/COOL/FAN ONLY mode. Press again to cancel the TURBO function,
and the fan speed will change to pre-setting before.
Note: Ё and Ё change: After inserting the batteries, in the off state within 3
minutes, press the TURBO button for more than 5 seconds to switch the Fahrenheit
(Ё) or Celsius (Ё) degree display.
5. DISPLAY: When the unit is ON, press the button, to switch off/on all lights or LED
display. And this function will be canceled when changing mode.
6. TIMER:
Use the button to set the TIMER, or cancel the TIMER.
TIMER OFF:
When the unit is ON, the timed OFF is programmed by pressing TIMER
button, the remote will display 6 hours pre-setting at first.
Set the rest time by pressing the button or until the needed rest time display, then
press TIMER button again to confirm.
TIMER ON: When the unit is OFF, the timed ON is programmed by pressing TIMER
button, the remote will display 6 hours pre-setting at first. Set the rest time by
pressing the button or until the needed rest time display, then press TIMER button
again to confirm. Later, the remote screen will keep display [TIMER] icon.
Note: When TIMER ON, it cannot select Sleep mode, but can pre-set Mode,
temperature, fan speed, ECO.
7. SLEEP:
Press the SLEEP button, all of the display lights will turn off after a
while, but the Sleep light is always on. In SLEEP mode, the air conditioner will
automatically adjust the temperature and fan speed to make the room more
comfortable during the night. The set temperature will automatically raise every
30-60 minutes and at most change six times until the set temperature is 81 or
82°F. This function can be selected when COOL or HEAT mode.
8. FAN SPEED: Press the FAN SPEED button to choose the fan speed options. You can choose Hi, Med, Lo or Auto speed in
COOL or HEAT mode and choose Hi, Med, Lo in FAN mode. When DRY mode, it is only Low fan speed.
9. MONEY SAVER:
When the unit is in COOL mode, press the button to MONEY SAVER function. In MONEY SAVER mode, the
unit will turn off once the room is cooled to the user set temperature. The unit will turn back on when the room temperature
rises above the user set temperature. Before the compressor starts, the fan motor will run for 20 sec., then it will stop for 10
min., and will repeat to provide a much more comfortable feeling and save energy.
10. Child Lock: pressing the button for more than 2 seconds to lock or unlock the remote controller. When locked, each
function button is not useful, and the lock icon will flash when press any button.
Battery size:
AAA
Note: Do not mix old and new batteries or different types of AAA batteries.