QUANTUM
™
LX EVAPORATOR CONTROL PANEL
COMMUNICATIONS SETUP
090.610-CS (MAY 2016)
Page 106
Q5 SERIAL COMMUNICATIONS PORT WIRING
GENERAL NOTE
The information that is presented here and on the
following pages, refers to the Interface board and
not the Q5 board. The Interface board was devel-
oped to make customer connections to the pro-
cessor easier, as the Q5 use connections that are
too small and delicate to easily utilize in the field.
RS-232 WIRING AND JUMPERS
With the introduction of the Q5/Interface board,
customer connections to RS-232 have been elimi-
nated. If RS-232 communications IS required,
these signals may be converted to RS-422/485,
and the appropriate available port(s) utilized.
RS-422/485 WIRING AND JUMPERS
All four Interface board serial communications
ports are capable of RS-485, and COMM-1 (P10)
and COMM-2 (P11) can additionally be configred
as either RS-422 or RS-485.
The following table describes the Interface board
RS-422 connector pinouts and their associated
communications signals:
RS-422 Signal Wiring
Connector
Pin #
Signal
COMM-1
(P10)
COMM-2
(P11)
5
GND
GND
4
TX+
TX+
3
TX-
TX-
2
RX+
RX+
1
RX-
RX-
RS-485 Signal Wiring
Connector
Pin #
Signal
COMM
1
(P10)
COMM
2
(P11)
COMM
3
(P17)
COMM
4
(P16)
3
GND
2
+TX/+RX
1
-TX/-RX
The following pictorial shows a cutaway view of
the Interface board, as well as the jumpers, LED’s
and signal pinouts to allow the end user to com-
municate to COMM-1 (P10) and COMM-2 (P11)
using RS-422/485 protocol, and to use COMM-3
(P16) to communicate via RS-485.
NOTE: COMM-
3 and COMM-4 do not have any associated
jumpers, and COMM-4 (P17) is reserved for I/O
board communications. Refer to the tables in
this section for the specifics on the jumper set
-
tings RS-422/485:
COMM-1
(P10)
RS-422
GND
+RX
-RX
+TX
-TX
RS-485
N/C
N/C
GND
+TX/+RX
-TX/-RX
COMM-2
(P11)
RS-422
GND
+RX
-RX
+TX
-TX
RS-485
N/C
N/C
GND
+TX/+RX
-TX/-RX
COMM-4
(P17)
RS-485
(RESERVED)
COMM-3
(P16)
RS-485
GND
+TX/+RX
-TX/-RX
RS-422/485 Connectors, Jumpers and LED Location
RS-422/485 (COMM-1, & COMM-2, P11) Board Jumpers
Jumper Title
Function
Jumper Setting
COMM-1
(P10
COMM-2
(P11)
J1
J7
RS-422 (4-Wire)
Default
3
2
1
1 - 2
Closed
RS-485
(2-Wire)
3
2
1
2 - 3
Closed
J2
J13
Pull Down
Default
1 Pin
Only
J3
J16
Pull Up
Default
1 Pin
Only
J5
J17
RS-422
Default
1 Pin
Only
RS-485
1 - 2
Closed
J6
J18
RS-422
Default
1 Pin
Only
RS-485
1 - 2
Closed
J4
J22
High Speed Target
Default
1 - 2
Closed
NOTE: The triangle symbol (
) denotes Pin 1 on con-
nectors.
Содержание QUANTUM LX Control Panel
