manualshive.com logo in svg

Frick IDC3-0406, Руководство пользователя

Поделиться
Скачать
Frick IDC3-0406 Скачать руководство пользователя страница 10

140.960-IOM (JUN 2016)

Page 10

IDCF & IDC3 EVAPORATIVE CONDENSERS

INSTALLATION

MODEL NUMBER

H (DISTANCE FROM LIFT

POINT TO LIFTING DEVICE)

IDCF-0406

4’

IDCF-0412

6’

TABLE 3. DISCHARGE SOUND ATTENUATION LIFT DIMENSIONS

Discharge 

Sound

Attenuation

Detail A

Figure 15 – Discharge Sound Attenuation Installed

3/8” x 1 1/4” Bolt

3/8” Flatwasher

3/8” Locknut

NOTICE

Discharge sound attenuation can be added at the time of 
order or as an aftermarket item.

Fan Cowl Extensions

Each fan cowl extension is 10 1/2” tall and up to four fan cowl 
extensions may be installed.
1.  Fasten the fan cowl extensions through the large diameter 

pre-punched holes using the provided hardware as shown 
in Figure 16, Detail A.

2.  Follow “Fan Guard Installation” instructions to install the 

fan guard.

NOTICE

Fan cowl extensions can be added at the time of order or 
as an aftermarket item.

OPTIONAL ACCESSORY INSTALLATION

Bottom Water Outlet

1.  The bottom connection seal, Figure 13, is typical for all bot-

tom remote sump outlets, and bypasses. Flange mounting 
hardware and gasket to be supplied by others.

2.  Bottom connection seal kit(s) ship in plastic tubs.

NOTICE

Some parts that ship loose are labeled with unique three 

key codes for identification purposes. These three key 

codes are referenced throughout this guide to identify 

parts to be assembled in the field.

Cold

Water

Basin

Backup
Ring

2 1/4” OD
Gasket

Gasket Provided by Others

Hardware Provided

by Others

Figure 13 – Bottom Water Outlet

Discharge Sound Attenuation (IDCF Option Only)

1.  Verify the mounting frame and clips are factory installed as 

shown in Figure 14.

2.  Lower the attenuator into position by aligning the bolt 

holes on the attenuator with the pre-existing bolt holes on 
the mounting clips. Be sure to follow the minimum height 
restrictions H found in Table 3 between the top of the dis-
charge sound attenuation and the apex of the crane cables 
supporting the load.

Lift image 

not to scale

Mounting 

Clips

Mounting 
Frame

H

Figure 14 – Sound Attenuation Clip Placement And Lift

Содержание IDC3-0406





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды