Friant FCNAHBC, Руководство по сборке, Страница: 7 / 7

7
Step 15: It is important to perform the reset
operation below before you use your My-Hite
table for the first time.
FIRST TIME USE:
RESET OPERATION
1. Lower the table to 24.5” by holding arrow down (V) button. Release button.
2. Press the arrow down (V) button again and hold till ASR shows on the display.
3. Release the button and the ASR will flash on the display
4. Hold the arrow down button again. Table will shift up and down slightly as it resets to
24.5”.
SET MINIMUM HEIGHT
SET MAXIMUM HEIGHT
1. Press the arrow down (V) button to get to desired minimum height.
Note: the arrow down button must be the last button pressed to set the minimum height. You
cannot press the arrow up button when trying to set the minimum height.
2. Hold “S” button till screen display flashes. Immediately press “S” button twice again.
3. Display will flash “000” and then show the set minimum height.
V
1. Press the arrow up ( ) button to get to desired maximum height.
Note: the arrow up button must be the last button pressed to set the maximum height. You
cannot press the arrow down button when trying to set the maximum height.
2. Hold “S” button till screen display flashes. Immediately press “S” button
twice again.
3. Display will flash “999” and then show the set maximum height.
TO PROGRAM THE MEMORY CONTROL PANEL:
Adjust the table to the desired height, press the S key and one of the three preset
buttons. This position is now saved. Once a preset button is pushed, the table will
automatically move to the preset height. Repeat this procedure for each preset button.
TROUBLESHOOTING MY-HITE
Error code Explanation Cause Solution
H01 Motor has
overheated Overuse 1. Let motor rest for 10 minutes.
2. Perform reset operation.
3. If problem persists
contact Friant customer
service
ERR,
ASR or
RST (solid
or flashing) System is
locked Various Reasons 1. Remove plug from electrical outlet for 15
seconds, then plug unit back in.
2. Perform reset operation.
3. If problem persists contact Friant customer
service to replace control panel
No display Control
Panel has
lost power Disruption in
power supply to
base 1. Remove plug from electrical outlet for 15
seconds, then plug unit back in.
2. Perform reset operation.
3. If problem persists contact Friant customer
service to replace control panel.
E01,
E02, or
E03 Excessive
weight
distribution Too much
weight (limit
exceeded)
or
Other problem
1. Check that weight on table does not exceed
limit.
2. Perform reset operation.
3. If problem persists
contact Friant customer
service to replace control panel
E07,
E08, or
E09 Signal
Interruption Signal is
interrupted
between leg
and computer 1. Perform reset operation.
2. If problem persists contact Friant customer
service
CLEAR MAXIMUM & MINIMUM HEIGHT
1. Table can be at
ANY HEIGHT
but
NOT
the minimum or maximum.
2. Hold “S” til display flashes. Release button.
3. Press “S” slowly, multiple times - until “555” shows on display.
Note: Display will show other codes, continue to press “S” until “555” shows.
4. Display will then show table height and can now move to any height between 24.5” and
50.1”.
NOTE :
If you cannot lower the table to the 24.5” height to perform reset operation,
you may need to clear out the maximum and minimum height (See instructions
below). Once completed, please return to the Reset Operation instructions.
SPECIAL CLEAR MINIMUM & MAXIMUM HEIGHT
1. Following is a special reset procedure when minimum and maximum height is set
within 1”
of each other:
2. Unplug unit for 10 minutes
3. Connect unit to power take care not to touch up or down arrows
4. Hold S button until it flashes
5. Let go and press S button 6 times in a row
6. 555 will show up on the display, minimum and maximum heights are now cleared.
July 2019
1980 West Avenue, 140th, San Leandro CA 94577 TEL: 510.535.5113 FAX: 510.535.5237 http://www.
friant.com