Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 946 | Manualshive

Страница: 946 / 1153

background image

Preface

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

21-9

21.3.3

Register Descriptions

The FlexCAN2 registers are described in this section. Note that there are three separate, identical
FlexCAN2 modules. Each register in the following sections is denoted with an ‘

x

’ that represents the

specified module.

21.3.3.1

Module Configuration Register (CAN

x

_MCR)

CAN

x

_MCR defines global system configurations, such as the module operation mode and maximum

message buffer configuration. Most of the fields in this register can be accessed at any time, except the
MAXMB field, which should only be changed while the module is in freeze mode.

0

1010

1010

Transmit a data frame whenever a remote request frame with the
same ID is received. This MB participates simultaneously in both the
matching and arbitration processes. The matching process
compares the ID of the incoming remote request frame with the ID of
the MB. If a match occurs this MB is allowed to participate in the
current arbitration process and the CODE field is automatically
updated to ‘1110’ to allow the MB to participate in future arbitration
runs. When the frame is eventually transmitted successfully, the
Code automatically returns to ‘1010’ to restart the process again.

0

1110

1010

the MBM as a result of match to a remote request frame. The data
frame will be transmitted unconditionally once and then the code will
automatically return to ‘1010’. The CPU can also write this code with
the same effect.

Address: Base + 0x0000

Access: User read/write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

MDIS FRZ

0

HALT

NOTRDY

0

SOFTRST

FRZACK

1

0

WRN

EN

MDISACK

0

0

SRX

DIS

MBFEN

W

Reset

0

1

0

1

1

0

0

1

1

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

0

0

0

0

0

0

0

0

0

0

MAXMB

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

Figure 21-3. Module Configuration Register (CAN

x

_MCR)

Table 21-6. Message Buffer Code for TX Buffers (continued)

RTR

Initial TX

Code

Code after

Successful

Transmission

Description

«
...
944
945
946
947
948
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: We Care Solar Страницы: 46

Бренд: IBC Страницы: 8

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Vent-Axia Страницы: 4

Бренд: Wittenstein Страницы: 52

Бренд: HIKVISION Страницы: 5

Бренд: Nexen Страницы: 28

Бренд: AMALGAMATED INSTRUMENT Страницы: 27

DMX-LED-DIMMER X9 HR

Бренд: DMX4ALL Страницы: 14

Бренд: Washify Страницы: 25

Бренд: microHAM Страницы: 64

Бренд: Danfoss Страницы: 2

Boiler Control TSBC

Бренд: Thermal Solutions Страницы: 48

Бренд: D+H Страницы: 16

Бренд: AMD Страницы: 264

Бренд: Knoll Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды