Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 1153

background image

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

Chapter 2
Signal Description

This chapter describes the external device signals, including a table of signal properties, detailed
descriptions of the available signals, and the I/O pin power/ground segmentation.

2.1

Block Diagram

To provide an extensive feature set as well as compatibility between the MPC5500 family of devices, the
majority of balls are assigned multiplexed signal functions.

shows only the signals that are

available on the device. Signal functions that are not available on this device are not shown in the diagram.
Primary signal functions that are not available on the device but are used as pin labels in the Ball Grid
Array (BGA) map are listed in

.

The 324 package has a limited number of balls which affects the following signals and features:

Refer to the last two columns in

for a comparison of available signals on the 324 package

compared to the VertiCal assembly.

NOTE

The Vertical assembly has ball connections for all the

available

signals on

the device.

Table 2-1. MPC5565 324 Package Limitations

Feature Signals

MPC5565 Design

324 Package

Maximum 24-bit EBI address bus

ADDR[8:31]_GPIO[4:27]; ADDR[8:11] are muxed
as alternate signals with the chip select signals
CS[0:3]_ADDR[8:11]_GPIO[0:3]. ADDR[8:11] is
also muxed with GPIO[4:7], providing four chip
selects

and

24-bit address bits.

ADDR[8:11]_GPIO[4:7] no balls available.
Use CS[0:3]_ADDR[8:11]_GPIO[0:3] to
choose between using chip select signals

or

maximizing the number of output address
signals ADDR[8:31]_GPIO[0:3, 8:31] for a
24-bit EBI address bus.

Maximum 32-bits wide EBI data bus

DATA[0:31]_GPIO[28:59]

16 balls available for a 16-bits wide
DATA[0:15]_GPIO[28:43]. There are no balls
available for DATA[16:31]_GPIO[44:59].

Four EBI write enable/byte enable

WE/BE[0:3]

Only two balls available (WE/BE[0:1])

EBI transfer error acknowledge

TEA_GPIO[71]

No ball available

EBI bus busy

BB signal not available. GPIO is available.

BB_GPIO[72] no ball available

EBI bus grant

BG signal not available GPIO is available.

BG_GPIO[73] no ball available

EQADC Event trigger inputs 0 and 1

ETRIG[0:1]_GPIO[111:112]

No balls available

General Purpose Input/output

GPIO[205]

No ball available

Calibration bus

Calibration bus is separate from the EBI but uses
the EBI controller. Refer to

for the

calibration bus signals.

No balls availables. These signals are only
available in the VertiCal assembly.

«
...
56
57
58
59
60
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Bartlett Страницы: 30

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: V2 Страницы: 12

Бренд: H3C Страницы: 5

Бренд: z21 Страницы: 2

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Clip Studio TABMATE

Бренд: CELSYS Страницы: 2

MIMIC HRNDWHEELS

Бренд: MRMC Страницы: 20

Бренд: Olsen Страницы: 4

SYSVRF AHU 10HP S

Бренд: SystemAir Страницы: 16

Бренд: Zapi Страницы: 30

Бренд: TSM Страницы: 2

Бренд: Parker Страницы: 64

TWRF1 SCR Series

Бренд: Metek Страницы: 36

Бренд: Tyco Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды