manualshive.com logo in svg

Freescale Semiconductor MCF52277, Справочное руководство

Продукт MCF52277 от Freescale Semiconductor - это микросхема с множеством функций для встраиваемых систем. Руководство по эксплуатации можно бесплатно загрузить с официального сайта Freescale Semiconductor. Здесь вы найдете подробное описание и инструкции по использованию данного устройства. Посетите manualshive.com, чтобы скачать Руководство по эксплуатации.

Поделиться
Скачать
background image

Synchronous Serial Interface (SSI)

MCF52277 Reference Manual, Rev. 1

25-34

Freescale Semiconductor

 

In network mode, data can be transmitted in any time slot. The distinction of network mode is each time 
slot is identified with respect to the frame sync (data word time). This time slot identification allows the 
option of transmitting data during the time slot by writing to the SSI_TX registers or ignoring the time slot 
as determined by the SSI_TMASK register bits. The receiver is treated in the same manner and received 
data is only transferred to the receive data register/FIFO if the corresponding time slot is enabled through 
SSI_RMASK.

By using the SSI_TMASK and SSI_RMASK registers, software only has to service the SSI during valid 
time slots. This eliminates any overhead associated with unused time slots. Refer to 

Section 25.3.18, “SSI 

Transmit Time Slot Mask Register (SSI_TMASK),”

 and 

Section 25.3.19, “SSI Receive Time Slot Mask 

Register (SSI_RMASK),”

 for more information on the SSI_TMASK and SSI_RMASK registers.

In two channel mode (SSI_CR[TCH] = 1), the second set of transmit and receive FIFOs and data registers 
create two separate channels (for example, left and right channels for a stereo codec). These channels are 
completely independent with their own set of interrupts and DMA requests identical to the ones available 
for the default channel. In this mode, data is transmitted/received in enabled time slots alternately from/to 
FIFO 0 and FIFO 1, starting from FIFO 0. The first data word is taken from FIFO 0 and transmitted in the 
first enabled time slot and subsequently, data is loaded from FIFO 1 and FIFO 0 alternately and 
transmitted. Similarly, the first received data is sent to FIFO 0 and subsequent data is sent to FIFO 1 and 
FIFO 0 alternately. Time slots are selected through the transmit and receive time slot mask registers 
(SSI_TMASK and SSI_RMASK).

25.4.1.2.1

Network Mode Transmit

The transmit portion of SSI is enabled when the SSI_CR[SSI_EN and TE] bits are set. However, for 
continuous clock when the TE bit is set, the transmitter is enabled only after detection of a new frame sync 
(transmission starts from the next frame boundary).

Normal start-up sequence for transmission:

•

Write the data to be transmitted to the SSI_TX register. This clears the TDE flag.

•

Set the SSI_CR[TE] bit to enable the transmitter on the next word boundary (for continuous clock).

•

Enable transmit interrupts.

Alternately, the user may decide not to transmit in a time slot by writing to the SSI_TMASK. The TDE 
flag is not cleared, but the SSI_TXD port remains disabled during the time slot. When the frame sync is 
detected or generated (continuous clock), the first enabled data word is transferred from the SSI_TX 
register to the TXSR and is shifted out (transmitted). When the SSI_TX register is empty, the TDE bit is 
set, which causes a transmitter interrupt (if the FIFO is disabled) to be sent if the TIE bit is set. Software 
can poll the TDE bit or use interrupts to reload the SSI_TX register with new data for the next time slot. 
Failing to reload the SSI_TX register before the TXSR is finished shifting (empty) causes a transmitter 
underrun error (the TUE bit is set). If the FIFO is enabled, the TFE flag is set in accordance with the 
watermark setting and this flag causes a transmitter interrupt to occur.

Clearing the TE bit disables the transmitter after completion of transmission of the current frame. Setting 
the TE bit enables transmission from the next frame. During that time the SSI_TXD port is disabled. The 
TE bit should be cleared after the TDE bit is set to ensure that all pending data is transmitted.

Содержание MCF52277

































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MCF52277

IEI Technology KINO-KBN-i2 Quick Installation Manual preview
KINO-KBN-i2
Бренд: IEI Technology Страницы: 21
Paradyne 3172 Quick Reference preview
3172
Бренд: Paradyne Страницы: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Бренд: Paradyne Страницы: 2
Lorex LNR100 SERIES Instruction Manual preview
LNR100 SERIES
Бренд: Lorex Страницы: 186
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Бренд: ZyXEL Communications Страницы: 20
Galaxy Hunter Series Quick Start Manual preview
Hunter Series
Бренд: Galaxy Страницы: 30
Aewin Technologies SCB-9651 User Manual preview
SCB-9651
Бренд: Aewin Technologies Страницы: 86
Paradyne SMD2000-24E Installation Instructions Manual preview
SMD2000-24E
Бренд: Paradyne Страницы: 28
BenQ QCast User Manual preview
QCast
Бренд: BenQ Страницы: 38
IBASE Technology ET880 Series User Manual preview
ET880 Series
Бренд: IBASE Technology Страницы: 64
NCR VOYIX 7772-K141 Kit Instructions preview
VOYIX 7772-K141
Бренд: NCR Страницы: 10
LinMot E1100 Series Manual preview
E1100 Series
Бренд: LinMot Страницы: 62
NetApp NS224 Instructions Manual preview
NS224
Бренд: NetApp Страницы: 28
Epson C32C824151 - UB E02 Print Server Technical Reference Manual preview
C32C824151 - UB E02 Print Server
Бренд: Epson Страницы: 84
Epson C11CA31101 User Manual preview
C11CA31101
Бренд: Epson Страницы: 168
Epson B80818 Series Quick Manual preview
B80818 Series
Бренд: Epson Страницы: 3
Alvarion BreezeACCESS II System Manual preview
BreezeACCESS II
Бренд: Alvarion Страницы: 324
StarTech.com PEX8S952 Manual preview
PEX8S952
Бренд: StarTech.com Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды