Freescale Semiconductor KW2xD Series Скачать руководство пользователя

Страница: 16 / 42

TWR-KW2xDxxx

Tower KW2xDxxx Hardware Reference Manual, Rev. 0.2

3-4

Freescale Semiconductor

Temperature

Operating temperature (see note)

-40

+25

+70

°C

• Operating temperature is limited to +70

°C due to switches. Basic circuit is good
for a maximum temperature of +85 °C.

Storage temperature

-30

+25

+70

°C

802.15.4 Frequency range

2405

2480

MHz

All 16 channels in the2450 MHz band

RF Receiver

Saturation (maximum input level)

+10

dBm

Sensitivity for 1% packet error rate (PER)
(+25 °C)

-100

dBm

RF Transmitter

RF Power Output

-32

+10

dBm

Programmable in 2dB steps

2nd harmonic

<-50

<-40

dBm

Measured with output power set to nominal
(0 dBm) and temperature @ 25°C. Trap filter
is needed.

3rd harmonic

<-50

<-40

dBm

Measured with output power set to nominal
(0 dBm) and temperature @ 25°C. Trap filter
is needed.

Regulatory Approval

FCC

Product is approved accordingly to the FCC
part 15 standard

CE (ETSI)

Product is approved accordingly to the EN
300 328 V1.7.1 (2006-10) standard

CE (EMC)

Product is approved accordingly to the EN
301 489-1 V1.6.1 (2005-09) and EN 301
489-17 V1.2.1 (2002-08) standards

Safety

Product is approved accordingly to the IEC
60950-1 and EN 60950-1, First Edition
standards

Environment

RoHS

Product complies with the EU Directive
2002/95/EC of 27 January 2003

WEEE

Product complies with the EU Directive
2002/95/EC of 27 January 2003

Table 3-1. TWR-KW2xDxxx Specifications (continued)

Parameter

Units

Notes/Conditions

Содержание KW2xD Series











































Результаты поиска

Содержание KW2xD Series

Отзывы:

Похожие инструкции для KW2xD Series

Бренды по названию

Популярные бренды

Freescale Semiconductor KW2xD Series, Справочное руководство

Результаты поиска

Содержание KW2xD Series

Отзывы:

Похожие инструкции для KW2xD Series

Бренды по названию

Популярные бренды