MODE SELSECT
6.Command Specification
SONY AIT-1 Turbo drive SDX-450V series Ver.1.0
6-51
6.7.8. Append Partition (32h)
The Append Partition Command is available in the AIT mode. The Append Partition Command takes effect if the
current partition is the last partition. When the command is issued in the last partition, SDX-450V will automatically
space to the EOD area find the bottom of the Device Area, and then create a new partition. If the command is issued
in any other partition, SDX-450V will return the CHECK CONDITION status (83h/97h Current Partition is no the last
partition).
Table 6-43: Append Partition Page
Bit
Byte
7 6 5 4 3 2 1 0
0
Reserved
Page Code (32h)
1
Page Length (8)
2
Reserved
3
Reserved
4
Reserved PSUM
(10) Reserved
5
Reserved
6
Reserved Partition
units
7
Reserved
8
(MSB)
Partition Size Descriptor
9
(LSB)
PSUM
Partition Size Unit of Measured field defines the units in which the Partition Size value selects the partition size,
which in the case of this drive is Megabytes. Therefore, the drive returns 10b for a MODE SENSE and will only
accept this value for a MODE SELECT, otherwise a CHECK CONDITION status is returned with an ILLEGAL
REQUEST Sense Key set.
Partition units
The Partition Size Units of Measure (PSUM) field defines the units used in the partition size descriptors. A logical unit
is not required to retain the Partition Size Unit of Measure used to partition the medium. The PSUM field is defined in
following table.
Code Description
Support
00B
Bytes (unit of one)
Optional
01B Kilobytes
(10
3
bytes)
Optional
10B Megabytes
(10
6
bytes)
Optional
11B 10
x
bytes (
x
= partition units field)
Optional
Partition Size Descriptor
Partition size in megabytes, in binary notation. Bytes 8, 9: Partition Size Descriptor. For a Mode Sense Command,
the value in this field is invalid unless the Mode Sense Command follows a successful Mode Select Command Page
32. Therefore, on power-up without a Mode Select Page 32h, the Current Page 32h Partition Size Descriptor should
be set to the default value of 00 00. There is no relation between this field and the IDP bit in the parameter block of
Mode Select Page 11h.
Содержание FC TapeWare AIT-450i
