manualshive.com logo in svg

Franklin Fueling Systems UPP PIPING, Руководство по установке

Поделиться
Скачать
Franklin Fueling Systems UPP PIPING Скачать руководство пользователя страница 8

6

UNCOILING PIPE
CUTTING STRAPS

Coiled pipe is delivered with four straps 

that secure the coil. The coil has a “tail” 

section that protrudes outside of the coil 

circumference:

•  The “tail” must be secured to a 

stable anchor point with rope or 

other means before you can start 

uncoiling.

•  Once anchored the coils is slowly 

rolled cutting the straps in sequence 

as the coil is uncoiled,

•  Failure to follow this procedure 

can result in severe injury as the 

coils energy will be release in an 

uncontrolled fashion.

•  Staking is required every 1m to hold 

coil in place during relaxation period.

•  Once a coil is completely uncoiled, 

the far end of the coil must be 

secured to a stable anchor point.

 

Coil Weights

RELAXING AND ROUTING

Staking coil:

•  Metal or wood stakes at least 1-2 meter in length and at least 30 mm x 30 mm are recommended for every 

1 meter of coiled pipe.

•  Stakes should be offset on each side to provide stability every .5 meters.

•  Coils should be uncoiled and laid out as straight as possible, as much as the site allows.

NOTE:

 Some sites may require coils to be wrapped around the perimeter and use extras stakes to make secure 

bends.

Содержание UPP PIPING

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды