Franklin Fueling Systems UPP PIPING Скачать руководство пользователя страница 3

1

INTRODUCTION

LEGAL NOTICES

The information in this publication is provided for reference only. While every effort has been made to ensure the 

reliability and accuracy of the information contained in this manual at the time of printing, we recommend that you 

refer to “franklinfueling.com” for the most current version of this manual. All product specifications, as well as 

the information contained in this publication, are subject to change without notice. Franklin Fueling Systems does 

not assume responsibility and expressly disclaims liability for loss, damage, or expense arising out of, or in any 

way connected with, installation, operation, use, or maintenance by using this manual. Franklin Fueling Systems 

assumes no responsibility for any infringement of patents or other rights of third parties that may result from use 

of this manual or the products. We make no warranty of any kind with regard to this material, including, but not 

limited to, the implied warranties of merchantability and fitness for a particular purpose.
Copyright © 2021 Franklin Fueling Systems, LLC, Madison, WI 53718. All world rights reserved. No part of this 

publication may be stored in a retrieval system, transmitted, or reproduced in any way, including, but not limited 

to, photocopy, photograph, magnetic, or other record, without the prior written permission of Franklin Fueling 

Systems.
UPP and GEMINI are registered trademarks of Franklin Electric Company, Inc,

CONTACT INFORMATION

franklinfueling.com

3760 Marsh Rd. • Madison, WI 53718 • USA

Tel: USA & 1 800 225 9787 • Fax: +1 608 838 6433

Tel: UK +44 (0) 1473 243300 • Tel: Mex 001 800 738 7610

Tel: DE +49 6571 105 380 • Tel: CH +86 10 8565 4566

CONVENTIONS

NOTE

: Provides helpful information, instructions to avoid damaging equipment, or potential environmental hazards.

 

WARNING:

 Indicates a potentially hazardous situation that could result in injury or death if not avoided.

SAFETY

Franklin Fueling Systems (FFS) equipment is designed to be installed in areas where volatile liquids such as 

gasoline and diesel fuel are present. Working in such a hazardous environment presents a risk of severe injury or 

death if you do not follow standard industry practices and the instructions in this manual. Before you work with 

or install the equipment covered in this manual, or any related equipment, read this entire manual, particularly the 

following precautions:

 

WARNING:

 Use only original FFS parts. Substituting non-FFS parts could cause the device to fail, which could 

create a hazardous condition and/or harm the environment.

 

WARNING:

 Follow all codes that govern how you install and service this product and the entire system. Always 

lock out and tag electrical circuit breakers while installing or servicing this equipment and related equipment. A 

potentially lethal electrical shock hazard and the possibility of an explosion or fire from a spark can result if the 

electrical circuit breakers are accidentally turned on while you are installing or servicing this product. Refer to this 

manual (and documentation for related equipment) for complete installation and safety information.

 

WARNING:

 Before you enter a containment sump, check for the presence of hydrocarbon vapors. Inhaling 

these vapors can make you dizzy or unconscious, and if ignited, they can explode and cause serious injury or 

death. Containment sumps are designed to trap hazardous liquid spills and prevent environmental contamination, 

so they can accumulate dangerous amounts of hydrocarbon vapors. Check the atmosphere in the sump regularly 

while you are working in it. If vapors reach unsafe levels, exit the sump and ventilate it with fresh air before you 

resume working. Always have another person standing by for assistance.

 

WARNING:

 Follow all federal, state, and local laws governing the installation of this product and its associated 

systems. When no other regulations apply, follow NFPA codes 30, 30A, and 70 from the National Fire Protection 

Association. Failure to follow these codes could result in severe injury, death, serious property damage, and/or 

environmental contamination. 

Содержание UPP PIPING

















Отзывы: