Franke La Marzocco FB-70 Скачать руководство пользователя страница 43

Страница: 43 / 67

7. Remove the blue and

white wires from the lower

portion of the thermostat.

8. Remove the upper wire.

9. Remove the upper gauge

tube and carefully move it to

the side.

10. Remove the lower

gauge tube and carefully

move it to the side.

11. Using a small Phillips

screwdriver, remove the trim

screws.

12. Gently flex the panel

downward and then rotate the

thermostat 90 degrees.

13. Pull the thermostat from

the well.

14. Apply a liberal amount of

thermal compound to the bel-

lows on the new thermostat.

15. Use a small cable tie to aid

in inserting the thermostat.

16. Insert the thermostat and

cable tie together.

17. Clip off the cable tie when

approximately 1/2” has been

inserted.

18. Press firmly on the thermo

stat to fully seat it into the well.

Содержание La Marzocco FB-70




































































Результаты поиска

Содержание La Marzocco FB-70

Отзывы:

Похожие инструкции для La Marzocco FB-70

Бренды по названию

Популярные бренды

Franke La Marzocco FB-70, Руководство по обучению

Результаты поиска

Содержание La Marzocco FB-70

Отзывы:

Похожие инструкции для La Marzocco FB-70

Бренды по названию

Популярные бренды