Franke La Marzocco FB-70 Скачать руководство пользователя страница 18

Страница: 18 / 67

Hydraulic Lines and Components

1. Inlet water tube to the coffee boiler.

2. Inlet water line feeding the inlet manifold.

3. Inlet water tube to the steam boiler.

4. Expansion valve.

5. Discharge fitting.

6. Discharge from the 3-way group valve.

7. Group valve.

8. Tube feeding water from the group valve to the banjo tube.

9. Tube feeding water from the flowmeter to the group valve.

10. Check valve for the coffee boiler.

11. (Same tube as #8).

12. Flowmeter.

13. Banjo tube (located inside of the group head).

14. Tube feeding water from the group to the flowmeter.

15. Tube feeding water from the flowmeter to the group valve.

16. Tube feeding water from the coffee boiler check valve to the “X” fitting.

17. Tube feeding water into the coffee boiler.

18. Tube feeding water to the gauge.

19. Tube feeding water to the expansion valve.

20. Tube feeding steam to the right steam assembly.

21. Tube feeding the top of the sight glass.

22. Tube feeding water to the hot water valve.

23. Tube feeding water to the steam boiler.

24. Auto-fill probe.

25. Pressure relief valve.

26. Vacuum breaker

27. Tube feeding steam to the pressure gauge.

28. Tube feeding steam to the pressure switch.

29. Tube feeding steam to the left steam assembly.

Содержание La Marzocco FB-70




































































Результаты поиска

Содержание La Marzocco FB-70

Отзывы:

Бренды по названию

Популярные бренды

Franke La Marzocco FB-70, Руководство по обучению

Результаты поиска

Содержание La Marzocco FB-70

Отзывы:

Бренды по названию

Популярные бренды