Franke La Marzocco FB-70 Скачать руководство пользователя страница 15

Страница: 15 / 67

Vacuum Breaker

The vacuum breaker is a mechanical valve located on the steam boiler.

As pressure builds in the boiler, steam pressure lifts a plunger, sealing

the boiler, allowing steam pressure to increase above atmospheric

pressure.

Expansion Valve

The expansion valve relieves front boiler pressure at 12 bar.

* The expansion valve is located in the drain box, which is

underneath the drip tray.

*It consists of a valve body, a valve seal and spring, which

are enclosed by an adjustable brass barrel.

*The expansion valve is adjusted by adding or relieving

tension on the spring by turning the adjusting barrel.

Safety Relief Valve

The pressure relief valve relieves boiler pressure at 1.8 bar

preventing the boiler from over-pressurizing. It is factory

adjusted and sealed and cannot be adjusted.

External Boost Pump

The boost pump increases existing water

pressure to 135 psi or 9 bar, which is

required to properly brew espresso.

* The pump pressure can be adjusted by

adjusting the screw on the side of

the pump.

* Rotating the screw clockwise will

increase pump pressure, while

rotating counter-clockwise will

decrease pump pressure.

*Ensure your waterline is stable, as

fluctuations in line pressure will

affect output pressure.

Relief Valve

Brass Washer

Washer

Body

Valve

Seal

Spring

Barrel

Outlet

Fitting

Check Valve

Inlet Fitting

Adjustment Screw

Pump

Motor

Clamp

Top Cap

Gasket

Teflon Cone

Body

Brass Washer

Содержание La Marzocco FB-70




































































Результаты поиска

Содержание La Marzocco FB-70

Отзывы:

Похожие инструкции для La Marzocco FB-70

Бренды по названию

Популярные бренды

Franke La Marzocco FB-70, Руководство по обучению

Результаты поиска

Содержание La Marzocco FB-70

Отзывы:

Похожие инструкции для La Marzocco FB-70

Бренды по названию

Популярные бренды