background image

14

02/2008

Operating instructions

Parquet floor sander Python C 3,2kW/50Hz 

with gentle lifting lever

7     

Operating the PYTHON C

7.1

Protective clothing and equipment

Caution! Wear hearing protectors!

The supplied hearing protectors must be worn when using the machine.

The following sound level values have been measured for the parquet floor sander 

PYTHON C according to DIN 45 645:

Idle mode

LEQ = 85 dB(A)

Working mode

LEQ = 87 dB(A)

The noise produced when the machine is working depends on various factors. Local 

conditions such as room size and quality of the floor affect noise development.

Caution! Wear a respirator!

When using the parquet floor sander PYTHON C and when disposing of the sanding 

dust, always wear a respirator (see chapter 7.3 and 7.4). Wear the respirator which is 

supplied with the accessories.

Caution! Wear safety goggles! 

When using the parquet floor sander PYTHON C and when working on PYTHON C, 

always wear safety goggles to protect your eyes.

Caution! Wear proper working clothing!

When using the parquet floor sander PYTHON C and when working on PYTHON C, 

never wear loose clothing. This can get caught up in moving parts.

Содержание 48666





















































Отзывы: