Fral FD360 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 22

Fral FD360 Скачать руководство пользователя страница 18

FD

18

CHAPTER 8: TROUBLE SHOOTING

In the following pages are reported the most common troubles that can cause the unit to stop or to operate in
an uncorrect way.

Concerning the solutions, it is necessary to take an extreme care on the actions to adopt: an
excessive confidence may cause serious accidents to inexperienced people. It is advisable, once
the cause is detected, to contact our servicing people or trained people only.

8.1 UNIT UNDER ALARM

When red light is lit up, the unit is stopped and set under alarm condition.

To restore normal operating mode, it is necessary to detect and remove the cause of the alarm

PROBLEM

LED ON

PROBABLE CAUSE

CORRECTIVE ACTION

A

Unit does not

start

but alarm green

led

is off

None

Power supply missing

Provide power supply,

replace fuses

Power supply

led

Humidistat on set

Set a lower set point

Power supply

led,

Compressor thermal

protection enabled,

compressor defective

Let the compressor cool

down, replace compressor

defective

Power supply

led,

Compressor thermal

protection enabled,

compressor defective

fan defective

Let the compressor cool

down, replace compressor

defective, replace fan

defective

Any led

Electronic board or led

Board defective

Replace defective board

«
...
16
17
18
19
20
...
»

Содержание FD360























Отзывы:

Нет отзывов