FPT CURSOR 87TE3 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 30

FPT CURSOR 87TE3 Скачать руководство пользователя страница 24

26



Install blow-by body (1) with related seal and lock screws (2) at
required torque.



Install cover (3) and lock screws (2) at required torque.

Change auxiliary member belt

Please refer to the information provided for checking the belt tension.

NOTE

:

Belt tensioner is automatic, therefore no further adjustment

are required after installation

Check tension and state of the auxiliary member

drive belt

Only proceed with the engine stopped and at a low temperature, so
as to avoid the risk of burning.

Refers to engines with automatic tensioning devices



Remove any casing protecting the pulleys.



Check that the belt is not torn or worn, and that there are no
lubricants or fuel on it. If this is not the case, replace it.



At the same time, make sure that the tensioning device is working
properly, proceeding as indicated in the figure.



Replace the guard casing in its housing, and lock all the retaining
elements.

12_007_C

12_009_C

«
...
22
23
24
25
26
...
»

Содержание CURSOR 87TE3































Отзывы:

Нет отзывов