OPERATING INSTRUCTIONS
STU 720V1.0
18
Information Display Period
If the period of time that the Information box is displayed is either
too long or too short, change the Information box display time as
follows:
1
Press MENU on the RCU.
The Main Menu options list is displayed.
2
On the RCU, press to highlight Information Display Period.
3
Press OK.
The Information Display Period screen is displayed.
4
Press or to change the information display period (in
seconds).
5
Press OK to confirm the new time or EXIT to cancel the
screen. The Main Menu is displayed.
6
Press EXIT or MENU to return to the service.
Local Time
The STU acquires the time ‘over the air’ from the Broadcaster.
There is therefore no need for the usere to adjust the time,
however the correct time zone is required for the STU to display
the correct time for that region. The STU is able to automatically
select these values.
The Local Time is controlled from the Local Time menu which is
located under ‘ADVANCED OPTIONS’. The STU operates in two
main modes being AUTOMATIC or MANUAL. In Automatic mode
the region region is selected by FOXTEL over the air according to
your street address, it is recommended that the STU is operated in
the Automatic Mode. In the Manual mode the user can select the
region according to the instructions below.
1. Press the Menu button on the Foxtel remote.
2. Press the or
arrow and select Advanced Options.
3. Press OK.
4. Press the or
arrow and select Local Time.
5. Press OK.
6. Use or arrow to change Mode.
7. Press OK when finished.
8. Press the or
arrow and select Region.
9. Use or arrow to change Region.
10. Press OK when finished.
11. Press the or
arrow and select Local Time.
12. Use or arrow to set the Local Time. The arrow allows
you decrease the minutes by 30 minute intervals, while the
arrow allows you to increase the minutes by 30 minute
intervals.
13.Press OK when finished, then Press Menu button to exit to
normal viewing. To view the time, Press the yellow button on
you Foxtel remote.
Mailbox
The Service Provider can send global or individual messages over
the air. When a message has been received, the yellow front
panel indicator will be illuminated and the symbol will be
displayed on the TV screen.
To read the message do the following:
1
Press MENU on the RCU. The Mains Menu options list is
displayed.
2
On the RCU, press to highlight Mailbox.
3
Press OK. The Mail Messages screen is displayed.
4
Press OK to return to the Main Menu.
The front panel yellow indicator will be OFF and the mail
symbol will no longer be displayed.
Over The Air Software Download
Upgrades involve replacing the software (programs) in the STU with
improved software, adding more features and improving the existing
operation of the STU. This ensures that the STU does not have to be
replaced each time advances in technology occur. By replacing the
software, you virtually get a new STU.
Software upgrades normally take place automatically over-the-air. The
STU can be upgraded when it is in standby or while it is switched to a
service. The STU software cannot be upgraded if it is switched off at
the mains. It is strongly recommended that your STU is left in the
standby mode when you are not using it.
A message on the TVscreen will warn you that a software upgrade
will take place. Software upgrades usually take place in the early
morning and last approximately 9 minutes, during which time normal
satellite viewing is not possible. After the download is completed, the
STU will automatically return to the current service.
NOTE:
1. Whilst the STU is performing the Upgrade, never
remove power from the STU as this will stop the
upgrade process and will cause your STU to stop
functioning normally.
2. During the upgrade an Amber light will be
displayed on the front of the STU with numbers
and a rotating cursor.
Press OK to confirm selection
Press and
to select option
Change Dish Installation
Signal Detection
Information
TV Installation
Change Modem Settings
Local Time
Decoder Upgrade
Advanced Options
Local Time
Mode:
Region:
Local Time:
MANUAL
CUSTOM
14:36
29-09-2000
Use left and right arrows to select made
Press OK to exit.
UPGRADE
Checking for Upgrade.
Upgrade is active and will take approximately XXminutes
