Router
config router ospf
FortiGate-100A Administration Guide
01-28007-0068-20041203
165
config summary-address
Note:
In the following table, only the
router-id
keyword is required. All other keywords are
optional.
ospf command keywords and variables
Keywords and
variables
Description
Default
Availability
abr-type {cisco |
ibm | shortcut |
standard}
Specify the behavior of a FortiGate unit
acting as an OSPF area border router
(ABR) when it has multiple attached areas
and has no backbone connection.
Selecting the ABR type compatible with
the routers on your network can reduce or
eliminate the need for configuring and
maintaining virtual links. For more
information, see RFC 3509.
cisco
All models.
database-overflow
{disable | enable}
Enable or disable dynamically limiting link
state database size under overflow
conditions. Enable this command for
FortiGate units on a network with routers
that because of limited resources may not
be able to maintain a complete link state
database.
disable
All models.
database-overflow-
max-lsas
<lsas_integer>
If you have enabled
database-
overflow
, set the limit for the number of
external link state advertisements (LSAs)
that the FortiGate unit can keep in its link
state database before entering the
overflow state. The
lsas_integer
must
be the same on all routers attached to the
OSPF area and the OSPF backbone. The
valid range for
lsas_integer
is 0 to
4294967294.
10000
All models.
database-overflow-
time-to-recover
<seconds_integer>
Enter the time, in seconds, after which the
FortiGate unit will attempt to leave the
overflow state. If
seconds_integer
is
set to 0, the FortiGate unit will not leave
the overflow state until restarted. The valid
range for
seconds_integer
is 0 to
65535.
300
All models.
default-
information-metric
<metric_integer>
Specify the metric for the default route set
by the
default-information-
originate
command. The valid range for
metric_integer
is 1 to 16777214.
10
All models.
default-
information-
metric-type {1 | 2}
Specify the OSPF external metric type for
the default route set by the
default-
information-originate
command.
2
All models.
default-
information-
originate {always
| disable |
enable}
Enter
enable
to advertise a default route
into an OSPF routing domain.
Use
always
to advertise a default route
even if the FortiGate unit does not have a
default route in its routing table.
disable
All models.
default-
information-route-
map <name_str>
If you have set
default-information-
originate
to
always
, and there is no
default route in the routing table, you can
configure a route map to define the
parameters that OSPF uses to advertise
the default route.
No
default.
All models.
Содержание FortiGate 100A
