Forney 125 FC Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 28

Forney 125 FC Скачать руководство пользователя страница 23

23

WWW.FORNEYIND.COM

A shorted nozzle results when spatter buildup bridges the insulation in the nozzle allowing welding

current to flow through it as well as the contact tip. When shorted, a nozzle will steal welding

current from the wire whenever it contacts the grounded work piece. This causes erratic welds

and reduced penetration. In addition, a shorted nozzle overheats the end of the gun which can

damage the front-end of the gun.

TESTING FOR A SHORTED NOZZLE

Arcing between the nozzle and the work piece always means the nozzle is shorted, but this can be hard

to detect through the lens of a welding helmet. The following testing method is another way to tell if a

nozzle is shorted.
With the welder unplugged from the AC power source, touch the probes of an ohmmeter or continuity

tester to the end of the contact tip and the outside of the nozzle. If there is any continuity at all, the nozzle

is shorted. Clean or replace as needed.

«
...
21
22
23
24
25
...
»

Содержание 125 FC





























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды