Formula Sound FF2.2 Скачать руководство пользователя страница 3

Power Supply 
 

The FF2.2 has an external power supply, this consists of a the power supply block and a mains 
cable with local style mains connector at one end and IEC style at the end that plugs into the body 
of the remote power supply block. 
 
The FF2.2 has a flying cable with a 7 pin connector on the end, this 7 pin connector plugs into the 
remote power supply block, this connector needs to be plugged in to the mating connector on the 
remote power supply block and then the outer of the connector turned to screw the connector into 
place. 
 
The power supply block has a IEC inlet with mains power switch, a green neon indicates when 
the power is on. The FF2.2 uses 3 power rails (+VE, -VE & 5V) which each have a screw in fuse, 
see appendix drawing for details. 
 
The FF2.2 should be switched on and off using the switch by the IEC connector on the remote 
power supply block.   
 
The Mixer has a fully regulated internal power supply that is designed to operate on   
220-240Vac or 110-120Vac, a label on the outside will indicate which mains supply your remote 
power supply requires.   
 

DAMAGE MAY RESULT IF THE UNIT IS CONNECTED TO THE WRONG   
SUPPLY VOLTAGE.   
 

 Mains fuse sizes are 800mA anti-surge for 220-240Vac and 1.5A anti-surge for 110-120Vac   
operation.   
 
It is important for safety reasons that the correct fuse sizes are always used.  
 

Master Section 

 
Refer to appendix drawings for positions of controls, inputs and settings accessible through 
the base of the FF2.2. Drawings indicate positions and functions, FF2.2 may differ. 
 

Outputs 

 
Master and Booth outputs are available in balanced stereo on XLR connectors along with 
unbalanced stereo outputs for each on RCA connectors (the booth output is called record on the 
RCA connector). 
 
There is also a mono output on XLR with a switch accessible through the base of the unit that 
allows the selection of either mono master or sub bass. 
 
Master and booth each have volume controls on the front panel, additionally there is a booth pan 
pot accessible through the base together with a switch that allows the booth to be switched to 
mono should it be required. 
 
Master and booth each have 12 LED stereo metering indicating output level in dB. 

 

Содержание FF2.2
















Отзывы: