formlabs Form Cure L Скачать руководство пользователя страница 14

Страница: 14 / 40

Safety

Read and understand this manual and its safety instructions before using the Form
Cure L. Failure to do so can result in serious injury or death.

Supervise young or inexperienced users to ensure enjoyable and safe operation.
These instructions contain warnings and safety information, as explained below:

DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or

moderate injury.

NOTICE indicates information considered important, but not hazard-related.

DANGER:

Isopropyl alcohol is a flammable chemical.

ENVIRONMENTAL HAZARD:

Uncured photopolymer resin is classified as hazardous to aquatic life.

CAUTION:

Do not touch hot surfaces.

MANDATORY ACTION: Refer to instruction manual/booklet.

MANDATORY ACTION: Grounding required.

MANDATORY ACTION: Disconnect before carrying out maintenance or repair.

MANDATORY ACTION: Wear eye protection.

MANDATORY ACTION: Wear thermal-insulating silicone gloves when handling hot build chambers.

3.1

Component and subsystem safety

3.1.1

General

The Form Cure L is a professional appliance that includes electronic components. As with
any such appliance:

•

Do not operate the device with a damaged cord or plug.

•

Ensure reliable grounding before connecting the device to power.

WARNING

DANGER

WARNING

CAUTION

NOTICE

Содержание Form Cure L









































Результаты поиска

Содержание Form Cure L

Отзывы:

Бренды по названию

Популярные бренды

formlabs Form Cure L, Инструкция по установке и использованию

Результаты поиска

Содержание Form Cure L

Отзывы:

Бренды по названию

Популярные бренды