background image

6

To remove the perforating wheels or the creasing wheel, first remove the shaft with the blade guides then remove the shaft 
with the perforating wheels. 

Remove the shaft by holding the bearing (29) and pulling it over the spring into the terminal position. Then push the whole 
shaft back including the bearing, and remove the shaft from the machine as shown below. 

Reverse the process to replace the shaft.

Removing Perforating and/or Creasing Wheels

29

Covers can be removed after paper processing has been finished and fully disconnected from the power supply. Before 
resuming work, the covers must be reattached and secured. The covers should be removed only by a trained technician.

NOTE:

 The covers should be removed only when service interference, belt replacement or feed roller pressure is required.

Removing Covers

The  pressure  of  the  separator  on  the  feed  tire  (30)  of  the 
feeding shaft must be adjusted to accurately feed the paper 
from the feeding table (1). 

Turn  the  separator  adjustment  wheel  (31)  clockwise  to 
increase  the  pressure  on  the  separator.  If  a  thicker  sheet 
is  fed  into  the  feeding  table,  the  pressure  of  the  separator 
should be decreased by turning the wheel counterclockwise.

Separator Pressure Adjustment

31

30

MyBinding.com

5500 NE Moore Court 

Hillsboro, OR 97124 

Toll Free: 1-800-944-4573 

Local: 503-640-5920

Содержание FD 90












Отзывы: