background image

4. After you are done pumping fuel, slowly remove the fuel filler
nozzle—allow about five seconds after pumping fuel before removing the
fuel filler nozzle. This allows residual fuel to drain back into the fuel tank
and not spill onto the vehicle.

Note:

A fuel spillage concern may occur if overfilling the fuel tank. Do

not overfill the tank to the point that the fuel is able to bypass the fuel
filler nozzle. The overfilled fuel may run down the drain located within
the fuel filler housing and to the ground.

If the check fuel fill inlet lamp or CHECK FUEL FILL INLET message
comes on, the fuel fill inlet may not have properly closed. The inlet may
have stuck open or debris may be preventing the inlet from fully closing.
At the next opportunity, safely pull off the road, turn off the engine,
open the fuel filler door and remove any visible debris from the fuel fill
opening. Insert either the fuel fill nozzle or the fuel fill funnel (see

Refilling with a portable fuel container

for funnel location) provided

with the vehicle several times to dislodge any debris and/or allow the
inlet to close properly. If this action corrects the problem, the check fuel
fill inlet lamp or CHECK FUEL FILL INLET message may not reset
immediately. It may take several driving cycles for the check fuel fill inlet
lamp or CHECK FUEL FILL INLET message to turn off. A driving cycle
consists of an engine start-up (after four or more hours with the engine
off) followed by city/highway driving. Continuing to drive with the check
fuel fill inlet lamp or CHECK FUEL FILL INLET message on may cause
the service engine soon lamp to turn on as well.

WARNING:

The fuel system may be under pressure. If you hear

a hissing sound near the fuel filler door (Easy Fuel

“no cap”

fuel system), do not refuel until the sound stops. Otherwise, fuel may
spray out, which could cause serious personal injury.

Choosing the right fuel

Use only UNLEADED fuel or UNLEADED fuel blended with a maximum
of 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol, leaded
fuel or any other fuel. The use of leaded fuel is prohibited by law and
could damage your vehicle.

Your vehicle was not designed to use fuel or fuel additives with metallic
compounds, including manganese-based additives.

Note:

Use of any fuel other than those recommended may cause

powertrain damage, a loss of vehicle performance, and repairs may not
be covered under warranty.

Maintenance and Specifications

349

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

Содержание 2011 Taurus

























































































































































































































































































































































































































Отзывы: