Ford 2011 Taurus страница 22 Скачать руководство пользователя

Страница: 22 / 408

To reset the oil monitoring system to 100% after each oil change,
perform the following:

1. Press and release SETUP to display “OIL LIFE XXX% HOLD RESET =
NEW”.

2. Press and hold RESET for two seconds and release to reset the oil life
to 100%.

UNITS

Displays the current units in English or Metric.

Press RESET to change between English and Metric.

AUTO HIGH BEAM (if equipped)

This feature automatically turns on your high beams if it is dark enough
and no other traffic is present.

Press RESET to turn the auto high beam on or off.

AUTOLAMP (SEC)

This feature keeps your headlights on for up to three minutes after the
ignition is switched off.

Press RESET to select the new Autolamp delay values of 0, 10, 20, 30,
60, 90, 120 or 180 seconds.

AUTOLOCK

This feature automatically locks all vehicle doors when the vehicle is
shifted into any gear, putting the vehicle in motion.

Press RESET to turn autolock on or off.

AUTOUNLOCK

This feature automatically unlocks all vehicle doors when the driver’s
door is opened within 10 minutes of the ignition being turned off.

Press RESET to turn autounlock on or off.

COLLISION WARN GAP (if equipped)

This allows you to adjust the sensitivity setting of the collision warning
system. See

Collision Warning System

in the

Driving

chapter for more

information.

Press RESET to change the sensitivity setting from high sensitivity <– –
– – –> to low sensitivity <–>.

COLLISION WARN CHIME (if equipped)

This feature warns the driver of a possible collision. See

Collision

warning system

in the

Driving

chapter for more information.

Instrument Cluster

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

Содержание 2011 Taurus

























































































































































































































































































































































































































Результаты поиска

Содержание 2011 Taurus

Отзывы:

Похожие инструкции для 2011 Taurus

Бренды по названию

Популярные бренды

Ford 2011 Taurus, Руководство пользователя

Результаты поиска

Содержание 2011 Taurus

Отзывы:

Похожие инструкции для 2011 Taurus

Бренды по названию

Популярные бренды