Ford 2011 Taurus страница 126 Скачать руководство пользователя | Manualshive

Страница: 126 / 408

background image

Integrated keyhead transmitter (IKT)

To replace the battery:

1. Twist a thin coin in the slot near
the key ring to remove the battery
cover (1).

Note:

Do not wipe off any grease on

the battery terminals on the back
surface of the circuit board.

2. Carefully peel up the rubber
gasket (2) from the transmitter if it
does not come off with battery
cover.

3. Remove the old battery (3).

Note:

Please refer to local regulations when disposing of transmitter

batteries.

4. Insert the new battery. Refer to the instructions inside the IKT for the
correct orientation of the battery. Press the battery down to ensure that
the battery is fully seated in the battery housing cavity.

5. Reinstall the rubber gasket and snap the battery cover back onto the
key.

Intelligent access key (IA key)

To replace the battery:

1. Remove the backup key from the
transmitter, then twist a thin coin in
the slot hidden behind the backup
key slot to remove the battery
cover.

Note:

Do not wipe off any grease on

the battery terminals or on the back
surface of the circuit board.

1

2

3

Locks and Security

126

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

«
...
124
125
126
127
128
...
»

Содержание 2011 Taurus

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 Taurus

Бренд: TBC Страницы: 12

Бренд: Axxess Страницы: 8

Бренд: Meta System Страницы: 16

Бренд: Ecco Страницы: 24

Бренд: Ranger design Страницы: 24

Бренд: Linear Logic Страницы: 8

Бренд: Needit Страницы: 2

KIT ParkingSensor 814

Бренд: Gemini Страницы: 6

2007 SLR Mclaren

Бренд: Mercedes-Benz Страницы: 425

Бренд: Fabbri Страницы: 32

Бренд: Whelen Engineering Company Страницы: 2

Бренд: Honda Страницы: 4

Бренд: Pet Gear Страницы: 4

Бренд: Reliant Страницы: 116

Бренд: ECS Electronics Страницы: 42

Бренд: RADICAL Страницы: 11

Бренд: UCANDAS Страницы: 4

Бренд: Buick Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды