Ford 2011 Edge страница 335 Скачать руководство пользователя | Manualshive

Страница: 335 / 403

background image

•

If required, add engine oil to the engine. Refer to

Adding engine oil

in this chapter.

•

Do not overfill the engine
with oil. Oil levels above this
mark may cause engine
damage.

If the engine is

overfilled, some oil must be
removed from the engine by an
authorized dealer.

7. Put the dipstick back in and ensure it is fully seated.

Adding engine oil

1. Check the engine oil. For instructions, refer to

Checking the engine

oil

in this chapter.

2. If the engine oil level is not within the normal operating range, add
only certified engine oil of the recommended viscosity. Remove the
engine oil filler cap and use a funnel to pour the engine oil into the
opening.

3. Recheck the engine oil level. Make sure the oil level is not above the
normal operating range on the engine oil level dipstick.

4. Install the dipstick and ensure it is fully seated.

5. Fully install the engine oil filler cap by turning the filler cap clockwise
until it stops.

To avoid possible oil loss, DO NOT operate the vehicle with the
engine oil level dipstick and/or the engine oil filler cap removed.

Engine oil and filter recommendations

Look for this certification
trademark.

Maintenance and Specifications

335

2011 Edge

(edg)

Owners Guide, 1st Printing
USA

(fus)

«
...
333
334
335
336
337
...
»

Содержание 2011 Edge




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 Edge

Dodge Charger TufBox

Бренд: TUFLOC Страницы: 6

Бренд: CITROËN Страницы: 301

DBALL2-HYUNDAI9

Бренд: Xpresskit Страницы: 13

2011 3500 Chassis Cab

Бренд: RAM Страницы: 92

BASIC TLL171231

Бренд: Tellur Страницы: 5

Бренд: Pyle Страницы: 2

Бренд: Saab Страницы: 92

Бренд: A-rival Страницы: 23

Бренд: Paser Страницы: 2

Бренд: Xblitz Страницы: 56

Бренд: Edelbrock Страницы: 2

Бренд: Mercedes-Benz Страницы: 93

Бренд: EZ-ON Страницы: 2

Бренд: Havis Страницы: 4

Бренд: walser Страницы: 8

Бренд: Honda Страницы: 76

Бренд: GAC MOTOR Страницы: 356

Бренд: Chevrolet Страницы: 402

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды