Ford 2006 Expedition Скачать руководство пользователя страница 149

Страница: 149 / 368

3. Enter the 5–digit entry code

4. Press and hold the 7

•

8. While holding the 7

•

8 press the 3

•

5. Release the 3

•

6. Release the 7

•

The user should receive a

horn chirp

to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been
enabled.

SECURILOCK

姟

PASSIVE ANTI-THEFT SYSTEM

SecuriLock

娂

passive anti-theft system is an engine immobilization

system. This system is designed to help prevent the engine from being
started unless a

coded key programmed to your vehicle

is used.

The SecuriLock

娂

passive anti-theft system is not compatible with

non-Ford aftermarket remote start systems. Use of these systems may
result in vehicle starting problems and a loss of security protection.

Theft indicator

The theft indicator is the flashing red indicator located on the dash
panel.

•

When the ignition is in the 1 (OFF/LOCK) position, the indicator will
flash once every 2 seconds to indicate the SecuriLock

娂

system is

functioning as a theft deterrent.

•

When the ignition is in the 3 (ON) position, the indicator will glow for
3 seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock

娂

system, the indicator will flash

rapidly or glow steadily when the ignition is in the 3 (ON) position. If
this occurs, the vehicle should be taken to an authorized dealer for
service.

2006 Expedition

(exd)

Owners Guide (post-2002-fmt)
USA

(fus)

Locks and Security

149

Содержание 2006 Expedition

















































































































































































































































































































































































Результаты поиска

Содержание 2006 Expedition

Отзывы:

Бренды по названию

Популярные бренды

Ford 2006 Expedition, Руководство пользователя

Результаты поиска

Содержание 2006 Expedition

Отзывы:

Бренды по названию

Популярные бренды