Ford 2006 Expedition Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 368

Ford 2006 Expedition Скачать руководство пользователя страница 116

Resuming a set speed

Press the RES (resume) control and
release it. This will automatically
return the vehicle to the previously
set speed. The RES control will not
work if the vehicle speed is not
faster than 30 mph (48 km/h).

Increasing speed while using speed control

There are two ways to set a higher
speed:

•

Press and hold the SET + control
until you get to the desired
speed, then release the control.
You can also use the SET +
control to operate the Tap-Up
function. Press and release this
control to increase the vehicle set
speed in small amounts by 1 mph
(1.6 km/h).

•

Use the accelerator pedal to get to the desired speed. When the
vehicle reaches that speed press and release the SET + control.

RES

SET

COAST

+

RES

SET

COAST

+

2006 Expedition

(exd)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

116

«
...
114
115
116
117
118
...
»

Содержание 2006 Expedition

















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды