manualshive.com logo in svg

Ford 2006 Expedition, Руководство пользователя

Поделиться
Скачать
Ford 2006 Expedition Скачать руководство пользователя страница 139

Make sure the liftgate is closed to prevent exhaust fumes from
being drawn into the vehicle. If you must drive with the liftgate

open, keep the vents open so outside air comes into the vehicle.

LUGGAGE RACK

Your vehicle is equipped with a roof
rack. The maximum recommended
load is 200 lbs (90 kg), evenly
distributed. If it is not possible to
distribute the load, position it as far
rearward as possible.

To adjust cross-bar position (if
equipped):

1. Loosen the thumbwheel at both
ends of the cross-bar (both
cross-bars are adjustable).

2. Slide the cross-bar to the desired
location.

3. Firmly tighten the thumbwheel at
both ends of the cross-bar.

Vehicles with a higher center of gravity such as utility and
four-wheel drive vehicles handle differently than vehicles with a

lower center of gravity. Utility and four-wheel drive vehicles are not
designed for cornering at speeds as high as passenger cars any more
than low-slung sport cars are designed to perform satisfactorily under
off-road conditions. Avoid sharp turns, excessive speed and abrupt
maneuvers in these vehicles. Failure to drive cautiously could result in
an increase risk of loss of vehicle control, vehicle rollover, personal
injury and death.

2006 Expedition

(exd)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

139

Содержание 2006 Expedition

















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды