Visual Inspection Chart
3. If the inspection reveals obvious concern(s) that can be readily identified, repair as necessary.
4. If the concern remains after the inspection, connect the diagnostic tool to the data link connector (DLC) located beneath the instrument panel and select the vehicle to be tested
from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
check that the program card is correctly installed.
check the connections to the vehicle.
check the ignition switch position.
5. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool manual.
6. Carry out the DATA LINK DIAGNOSTIC TEST. If the diagnostic tool responds with:
CKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to
Section 418-00
.
NO RESP/NOT EQUIP for instrument cluster (IC), refer to
Section 413-01
.
NO RESP/NOT EQUIP for message center module (MCM), front electronic module (FEM), or rear electronic module (REM), refer to
Section 419-10
.
SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out self-test diagnostics for the instrument
cluster.
7. If the DTCs retrieved are related to the concern, go to the Message Center Module Diagnostic Trouble Code (DTC) Index or the Instrument Cluster Diagnostic Trouble Code (DTC)
Index to continue diagnostics.
8. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.
Message Center Module Diagnostic Trouble Code (DTC) Index
Note: For a complete master list of all MCM DTCs, refer to
Section 419-10
.
Instrument Cluster Diagnostic Trouble Code (DTC) Index
Note: For a complete master list of all instrument cluster DTCs, refer to
Section 419-10
.
FEM Diagnostic Trouble Code (DTC) Index
Note: For a complete master list of all FEM DTCs, refer to
Section 419-10
.
REM Diagnostic Trouble Code (DTC) Index
Note: For a complete master list of all REM DTCs, refer to
Section 419-10
.
Mechanical
Electrical
Washer fluid level
Fuel tank
Engine coolant level
Accessory drive belt
Engine oil level
Brake fluid level
Central junction box (CJB) fuse(s):
28 (10A)
14 (10A)
10 (5A)
16 (10A)
9 (10A)
Battery junction box (BJB) fuse(s):
2 (10A)
13 (10A)
Circuitry
Loose or corroded connectors
Switches or sensors
DTC
Description
Source
Action
B1205 EIC Switch 1 Assembly Circuit Failure
MCM
GO to
Pinpoint Test D
.
B1676 Battery Voltage Out of Range
MCM
GO to
Pinpoint Test A
.
U2013 Compass Module — No Response
MCM
GO to
Pinpoint Test B
.
Scan Tool Displayed DTC Dealer Test Mode Displayed DTC
Description
Source
Action
U1041
D141
SCP (J1850) Invalid or Missing Data for Vehicle Speed
PCM
CARRY OUT the PCM self-test.
U1073
D073
SCP (J1850) Invalid or Missing Data for Engine Coolant
PCM
CARRY OUT the PCM self-test.
U1123
D123
SCP (J1850) Invalid or Missing Data for Odometer
ABS/TC CARRY OUT the ABS/TC self-test.
U2013
D013
Compass Module — No Response
ICM
GO to
Pinpoint Test D
.
DTC
Description
Source
Action
B1254 Air Temperature External Sensor Circuit Failure
FEM
GO to
Pinpoint Test E
.
DTC
Description
Source
Action
B2570 Right Lamp Outage Signal Circuit Short to Ground
REM
GO to
Pinpoint Test G
.
B2571 Left Lamp Outage Signal Circuit Short to Ground
REM
GO to
Pinpoint Test G
.
Page 3 of 12
2001 Windstar Workshop Manual
11/30/2009
http://www.fordtechservice.dealerconnection.com/pubs/content/...
