Ford 2001 Windstar страница 10 Скачать руководство пользователя

Страница: 10 / 12

REPAIR the circuit. TEST the system for normal operation.

CHECK CIRCUIT 767 (LB/OG) FOR OPEN

Measure the resistance between the FEM C191 pin 9, circuit 767 (LB/OG), harness side and the ambient temperature

sensor C182 pin 1, circuit 767 (LB/OG), harness side.

Is resistance less than 5 ohms?

Yes

GO to

REPAIR the circuit. TEST the system for normal operation.

CHECK CIRCUIT 767 (LB/OG) AND CIRCUIT 1310 (RD/LB) FOR SHORT TO BATTERY

Measure the voltage between the FEM C191 pin 9, circuit 767 (LB/OG), harness side and ground.

Measure the voltage between the FEM C191 pin 2, circuit 1310 (RD/LB), harness side and ground.

Is any voltage present?

Yes

REPAIR the circuit in question. TEST the system for normal operation.

INSTALL a new ambient temperature sensor. TEST the system for normal operation.

CHECK CIRCUIT 767 (LB/OG) AND CIRCUIT 1310 (RD/LB) FOR OPEN

Measure the resistance between the FEM C191 pin 2, circuit 1310 (RD/LB), harness side and the ambient temperature

sensor C182 pin 2, circuit 1310 (RD/LB), harness side.

Measure the resistance between the FEM C191 pin 9, circuit 767 (LB/OG), harness side and the ambient temperature

sensor C182 pin 1, circuit 767 (LB/OG), harness side.

Are the resistances less than 5 ohms?

Yes

GO to

REPAIR the circuit in question. TEST the system for normal operation.

CHECK CIRCUIT 1310 (RD/LB) FOR SHORT TO GROUND

Page 10 of 12

2001 Windstar Workshop Manual

11/30/2009

http://www.fordtechservice.dealerconnection.com/pubs/content/...

Содержание 2001 Windstar













Результаты поиска

Содержание 2001 Windstar

Отзывы:

Похожие инструкции для 2001 Windstar

Бренды по названию

Популярные бренды

Ford 2001 Windstar, Руководство по ремонту

Результаты поиска

Содержание 2001 Windstar

Отзывы:

Похожие инструкции для 2001 Windstar

Бренды по названию

Популярные бренды