FOR-A USF-105DADA Скачать руководство пользователя страница 18

Страница: 18 / 21

9-1. Settings to Distribute 10 Output Signals from 1 Input

When USF-105DADAs are installed into Slots 1 and 2 as shown below, settings to distribute 10
outputs from the Slot 1 input signal are explained in this section.

(1) Set the signal mode of USF-105DADA in Slots 1 and 2 to the same mode. (Default: AES

distribution mode) See Sec. 4

“Signal Mode Settings” for details.

(2) Set DS2 of USF-105DADAs as shown in the table below.

Slot 1 USF-105DADA - DS2 settings

Switch

Setting

Description

Switch 3

OFF

Uses input via rear panel BNC. (Default)

Switch 4

OFF

Switch 5

Outputs to Slot 2 through Internal Bus1.

Switch 6

OFF

(Default)

Switch 7

OFF

(Default)

Slot 2 USF-105DADA - DS2 settings

Switch

Setting

Description

Switch 3

Uses input via Internal Bus 1 and distributes from Slot1
out.

Switch 4

OFF

Switch 5-7

OFF

(Default)

Input

Signal

Содержание USF-105DADA






















Результаты поиска

Содержание USF-105DADA

Отзывы:

Бренды по названию

Популярные бренды

FOR-A USF-105DADA, Руководство по эксплуатации

Результаты поиска

Содержание USF-105DADA

Отзывы:

Бренды по названию

Популярные бренды