manualshive.com logo in svg

FOR-A USF-105DADA, Руководство по эксплуатации

Поделиться
Скачать
FOR-A USF-105DADA Скачать руководство пользователя страница 17

17 

9. Extended Distribution Using Multiple USF-105DADAs 

 

Internal Bus Configuration 

 

 

Applying  multiple  USF-105DADAs  enable  you  to  increase  the  distribution  number  via  a  USF  frame 

internal bus. 

Up to 4 USF-105DADAs can be applied and 20 distributed, from 1 input. Install USF-105DADAs in the 

internal bus slot that is the same as for the input signal. (Slot 1 to 4, Slot 5 to 8, or Slot 9 to 12) 

Set  DS2,  and  Switch  3  to  7  to  increase  distribution  number  via  an  internal  bus.  See  Sec.  3-4 

“DS2 

Switches 3 and 4: Input Signal Switches Settings

” and Sec. 3-5 “DS2 Switch 5, 6, and 7: Internal Bus 

Switch Output Settings

” for details on switch settings. 

 
 

IMPORTANT 

When  using  USF-105DADA  units  in  a  USF  frame  internal  bus,  apply  multiple  USF-105DADAs  to 
extend distributions. Other USF modules cannot be combined with USF-105DADA for this purpose. 
When using an internal bus, ensure that the settings do not affect other modules. 

 

 

Slot 

9 - 12 

Slot 

5 - 8 

Slot 

1 - 4 

Содержание USF-105DADA






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды