Fonrich FR-DCMG-MMPY Скачать руководство пользователя страница 2

Страница: 2 / 37

Table of Contents

..........................................................................................................................................

The main function

.....................................................................................................................................

Documentation statement

......................................................................................................................

Terminal definition

....................................................................................................................................

Controller connection diagram

.............................................................................................................

Ground connection and communication shield

...............................................................................

Operation interface display

............................................................................................................................

Key operation

.............................................................................................................................................

Initial interface display

.............................................................................................................................

Histogram interface

..........................................................................................................................

Channel current and power generation display interface

.....................................................

Parameter setting interface

..................................................................................................................

Current calibration setting interface

..........................................................................................

Software version number display interface

.............................................................................

Alarm status display interface

.............................................................................................................

Channel arc fault alarm interface

................................................................................................

Fault alarm clear interface

............................................................................................................

Items that can generate alarms can be set

..............................................................................

Alarm conditions

.....................................................................................................................................

Alarm message

................................................................................................................................

MODBUS Protocol definition

.......................................................................................................................

Communication format configuration

......................................................................................

Data frame format description (refer to Modbus RTU standard)

......................................

Function code description

............................................................................................................

........................................................................................................................

.........................................................

..........................................

Appendix

...........................................................................................................................................................

FAQ

..............................................................................................................................................................

Document revision record

....................................................................................................................

.................................................................................................................................................

Содержание FR-DCMG-MMPY






































Результаты поиска

Содержание FR-DCMG-MMPY

Отзывы:

Бренды по названию

Популярные бренды

Fonrich FR-DCMG-MMPY, Руководство пользователя

Результаты поиска

Содержание FR-DCMG-MMPY

Отзывы:

Бренды по названию

Популярные бренды