Follett HCC700A Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

background image

30

Ice machine disposition

Possible causes

Corrective action

FLASHING

ON or OFF

Legend:

OFF

ON

6. Ice machine is making ice.

Excessive water in bin or
coming into bin from transport
tube.

1. Failed water sensors. Processor

assumes there is no water when
there is water.

2. Blocked reservoir vent.
3. Defective water feed solenoid

valve. Stuck in open position.

1. Clean or replace water probe

assembly. Check wiring
connections.

2. Clean or replace vent tubes.
3. Replace water feed solenoid

valve.

7. Ice machine is not making ice.

Lo water.

1. Water supply is insufficient.
2. Low water pressure.
3. Defective water feed solenoid

valve. Stuck in closed position.

4. No water feed output from

PC board.

1. Restore water supply and check

water fi lters. If evaporator was
completely empty the reset
button may have to be pressed
to restart the ice machine.

2. Ice machine will eventually start

when water reaches normal lo
level.

3. Replace water feed solenoid

valve.

4. Replace PC board.

8. Service

required.

1. 30,000 hour bushing check.

1. Call Follett technical service

group at (877) 612-5086 or
+1 (610) 252-7301.

ATTENTION!

To prevent circuit breaker overload, wait 15 minutes before
restarting this unit. This allows the compressor to equalize and the
evaporator to thaw.

«
...
28
29
30
31
32
...
»

Содержание HCC700A













































Отзывы:

Нет отзывов

Похожие инструкции для HCC700A

Бренд: Bartscher Страницы: 52

Бренд: Bartscher Страницы: 30

Бренд: acaia Страницы: 12

Бренд: Waring Страницы: 46

Бренд: Kalorik Страницы: 24

Бренд: Klarstein Страницы: 44

Бренд: Midea Страницы: 9

Coffee Maker 745-112

Бренд: Ide Line Страницы: 14

Taste Control CE4498

Бренд: SOLAC Страницы: 84

Бренд: Gastroback Страницы: 28

GranAroma SM6582

Бренд: Saeco Страницы: 590

Бренд: Hamilton Beach Страницы: 32

Бренд: Code Soft Страницы: 51

Бренд: Cobra Systems Страницы: 16

ARNO KRUPS Nescafe Dolce Gusto KP10 Series

Бренд: SEB Страницы: 52

Бренд: Chard Страницы: 8

Dual Brew Pro CFP300

Бренд: Ninja Страницы: 15

Бренд: SABROE Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды