background image

Page 5 of 12 

To assemble the boat you will first complete the frame, not including the seat assembly. 
The  frame  is  then  inserted  into  the  skin  and  the  stern  end  expanded  until  the  skin  is 
tight lengthwise. Please read all the instructions, and assemble slowly and carefully the 

first time.

   

 
 

 

 
 
1. Begin by checking the contents of the bag to be sure all parts are present.   
 
2.

 

Locate the bundle of tubing consisting of the curved bow end and the bottom keel. Engage the shock-

corded joints on these pieces to form a straight bottom keel. Lay this assembly on its side. 
 
3.  Locate  the  bow  deck  strut.  Connect  the  shock-corded  joint,  and  then  snap  the  end  with  the  blue  dot 
onto the short tube (also marked with a blue dot) fixed to the top of the curved bow end. Ensure the snap 
button engages the hole.   
 
4.  Now  assemble  the  two  upper  longeron  (gunwale)  bundles,  identified  by  the  red  dots.  These  are  pre-
bent at the factory and may look strange until the crossframes are in place.  There will be a right and left 
gunwale,  and  they  are  correctly  positioned  when  the  Velcro  is  on  the  outside  edge  of  the  boat  and  the 
Velcro ends each match the position of the adjacent tube. 
 

5.  Join  the  gunwales  to  the  curved  bow  end  and 
bottom  keel  assembly.  These  go  on  the  top 
butterfly fixtures next to the red dot on the curved 
portion  of  tubing,  with  the  screw  head  facing  up 
(see photo at left). 
 
Depress the snap button at the end of the gunwale 
and  move  the  3”  slider  back  to  expose  the  slot  in 
the black molded end. Slide the slot onto a wing of 
the  butterfly  fixture  from  the  side,  so  that  the 
screw is in the cutout of the wing. Move the slider 
back  in  position  until  the  snap  button  pops  up. 
Turn  the  assembly  on  its  other  side  and  join  the 
second gunwale in the same manner.  

 
 

 
6. Repeat this procedure with the lower longeron bundles, identified by the green dots.  These longerons 
attach to the lower butterfly fixture, also marked with a green dot. Position the deck strut so that it points 
forward and is out of the way. 
 

Содержание Citibot













Отзывы: