CONTENTS
PRELIMINARY N
NOTES
The Oblique electric wall heater provides convected heating in conjunction with a visual fuel effect display.
The appliance is designed for indoor use, and can be flat wall mounted in the majority of wall positions antici-
pated. However as an alternative, it can be wall mounted in a corner location using the corner mounting brack-
et. The appliance can be be located in any household room, with the exception of bathrooms. Read all of the
instructions before commencing installation. Retain for future reference and pass on as necessary to subsequent
owners of the appliance.
DO NOT use this appliance immediately below a fixed socket outlet.
DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where
water/moisture could present a hazard.
CAUTION: TThis aappliance m
must nnot bbe uused iin cconjunction w
with aany ttimer, pprogrammer oor tthermal ccontrol, oor
any oother ddevice tthat w
will sswitch oon tthe aappliance aautomatically, aas aa ffire rrisk m
may ooccur iif tthe hheaters aare aacci-
dentally ccovered oor ddisplaced. N
Note: TThe hheater ooutlet iis llocated oon tthe ttop ssurface bbehind tthe ffront fframe.
Do not allow the heater to be covered as this may cause overheating. Additionally, DO NOT place any items on
top of this appliance. The appliance must not be placed near curtains or similar material. A clearance space of
at least 500mm should be allowed in front of the appliance.
The eelectrical ssocket tthat tthe aappliance uuses M
MUST bbe eeasily aaccessible. D
Do nnot rroute tthe ssupply ccord ddirectly
over oor aabove tthe hheater uunit. IIf tthe ccord iis ddamaged, iit m
must bbe rreplaced bby aa sservice aagent oor ccompetent pper-
son.
APPLIANCE D
DATA
ELECTRICAL INSTALLATION REQUIREMENTS
The appliance is supplied with a pre-wired 3-pin BS1363 plug (13 Amp fuse rated), and 2 metre cable. A stan-
dard switched outlet/wall socket, (including earth provision), must therefore be located within this distance, and
be easily accessible in order to isolate the supply for maintenance and cleaning. This socket
must not be mount-
ed behind or above the appliance. Note: the pre-wired 3-pin plug should not be removed, as this may invalidate
warrenty.
It is recommended that the installation should be protected by a 30mA RCD, (Residual Circuit Device),
either via the existing main consumer unit if fitted, or by a dedicated device as part of this installation.
1
Section Contents
PPage N
No
1.0
Preliminary Notes
1
2.0
Appliance Data/Specifications
1
3.0
Electrical Installation Requirements
1
4.0
Site Requirements
2
5.0
Clearances to Combustible Materials
2
6.0
Unpacking the Appliance
3
7.0
Component Checklist
3
1.0
Section Contents
PPage N
No
8.0
Preparing the Appliance
3
9.0
Fixing the Appliance
4
10.0
Operating the Appliance
6
11.0
Safety Cut-Out System
7
12.0 Maintenance - Lamp Replacement
7
13.0
Cleaning
8
14.0
Servicing
8
Weight ((kg):
11.2 kg (13.3kg including corner mounting bracket)
Dimensions ((mm):
H 675 x W 546 x D 171(excluding corner mounting bracket)
Voltage ((Volts):
230-240V a.c. 50Hz
Heating EElements:
2 x 900/1000 Watts
Supply C
Cord:
2 metres
Supply PPlug:
BS1363, (13A BS1362 Fused)
Location:
Indoor Use Flat or Corner Wall - Non Bathroom/Shower Rooms
Lighting:
1 x 60W Amber “bayonet connection” lamp
2.0
3.0
This aappliance cconforms tto EEuropean D
Directive:
73/23/EEC LLow V
Voltage ((Safety), aand C
CE M
Marking D
Directive.
IMPORTANT
THIS A
APPLIANCE MUST BE EARTHED
The m
manufacturer ddeclines aall lliabilities ffor iinjury tto ppersons, oor ddamage tto pproperty, rresulting ffrom ffailure tto
observe tthis rregulation, aand/or ffailure tto ffollow oor oobserve tthese iinstructions.
©
2007 Focal Point Fires plc.
