background image

www.fmuser.org 

www.fmuser.org 

 

10 

7. Power on Sequence 

7.1  Open  the  package,  check  appearance,  switch,  key  button,  socket,  and  interface  port  on  front 

and back panel. 

7.2 Turn power switch on the “OFF” position and connect power cord to power source. 

7.3 Connect audio, video, RF cable on the back panel. Connect RF out port to a 50 Ohm dummy 

load or antenna through a cable. 

7.4  Turn  power  switch  to  “ON”  at  the  back  panel,  then  turn  power  switch  to  “ON”  at  the  front 

panel. 

7.5 Turn off RF power. 

7.6 Set working parameters. 

7.7 Turn on RF power. 

8. System Control Logic 

8.1 RF Output Control 

      This TV transmitter’s RF output can be controlled by RF Switch, which is on the “Main Page” 

of the LCD. 

        When RF Switch is OFF, turn off RF power. 

        When RF Switch is ON, and the video signal input is normal, turn RF power on. 

8.2 Remote Control 

        When  remote  control  is  enabled,  remote  LED  on  front  panel  is  lit.  And  power  output  is 

controlled by remote host and can not be changed locally except “Remote” flag is disabled. 

 

RS232 or RS485 are used for remote control. User can ask either of this two. Before enabling 

remote control, baud rate and device address should be properly set. 

8.3 System Protection 

        In  some  urgent  cases  such  as  exceeded  forward  power,  reflect  power,  current  and  over 

temperature,  system  will  reboot.  If  it  is  failed  successive  3  times,  the  system  will  automatically 

turns off RF power and just acts display function. 

Содержание FU-300W





















Отзывы: