background image

11

More control throw

Less control throw

Horns

                             

Arms

a.

b.

c.

d.

e.

f.

EN

Clevis installation

1.Pull the tube from the clevis to the linkage.

2.Carefully spread the clevis, then insert the clevis pin into the 

desired hole in the control horn.

3.Move the tube to hold the clevis on the control horn.

Control horn and servo arm settings

The table shows the factory settings for the control horns

and servo arms. Fly the aircraft at the factory settings 

before making changes.

After flying,you may choose to adjust the linkage positions

for the desired control response.

Elevator

Rudder

Ailerons

Check the C.G. (Center of gravity)

When balancing your model, adjust the battery as necessary 

so the model is level or slightly nose down. This is the correct 

balance point for your model. After the first flights, the CG 

position can be adjusted for your personal preference.

1. The recommended Center of Gravity (CG) location for your 

model is(80-85mm) from the leading edge of the main wing 

(as shown) with the battery pack installed. Mark the location of 

the CG on top of the wing.

2. When balancing your model, support the plane at the marks 

made on the bottom of the main wing with your fingers or a 

commercially available balancing stand. This is the correct 

balance point for your model. Make surethe model is assembled

and ready for flight before balancing. 

    

 

80-85mm

Содержание A-10 Thunderbolt II V2














Отзывы: