FMI (V)KCCNE series Скачать руководство пользователя страница 31

Страница: 31 / 40

www.fmiproducts.com

116237-01M

VENTING SYSTEM

Conduct annual inspection of the venting

system following these guidelines:
1. Check areas of venting system that are

exposed to the weather for corrosion (rust

spots or streaks and, in extreme cases,

holes). Have these items replaced im

mediately by a qualified service person.

2. Remove the vent cap and shine a flashlight

into the vent. Remove any foreign material.

CLEANING AND MAINTENANCE

Continued

3. Check for evidence of excessive condensa

tion. Continuous condensation can cause

corrosion of caps, pipes and fittings and can

be caused by having excessive lateral runs,

too many elbows or exterior portions of the

system being exposed to cold weather.

4. Inspect joints to verify that no pipe section

or fitting has been disturbed and loos

ened. Check mechanical supports such

as wall straps for rigidity.

TROUBLESHOOTING

WARNING: Turn off fireplace and let cool before servicing. Only

a qualified service person should service and repair fireplace.

CAUTION: Never use a wire, needle or similar object to clean

pilot. This can damage pilot unit.

Note: All troubleshooting items are listed in order of operation.

POSSIBLE CAUSE

1. No gas supply or shutoff

valve is OFF

2. Air in gas line

3. Construction debris clog

ging pilot orifice

4. Low gas pressure

5. Kinked pilot line

Control valve is not opening

7. No power to unit or ignition

module or power trans-

former is bad

REMEDY

1. Check to see if you have gas

supply and that equipment

shutoff valve is opened

2. Repeat lighting procedure

several times to purge all air

out of lines. If after repeated

attempts appliance does not

light, call for qualified service

and repair

3. Remove debris and dirt,

inspect and clean any other

possible obstructions

4. Contact your gas supplier to

check pressure

5. Have a qualified technician

replace pilot line

6. Replace control valve (Refer to

Replacement Parts

, page 34)

7. Check that main power is on

and that all wire connections

are made correctly to ignition

model (see

Wiring Diagram

page 27). Check for 24 VAC

at secondary side of trans-

former. If 24 VAC is present

and module does not oper-

ate, have module replaced

otherwise have transformer

replaced

OBSERVED PROBLEM

Ignitor will not spark or pilot

will not light

Содержание (V)KCCNE series









































Результаты поиска

Содержание (V)KCCNE series

Отзывы:

Похожие инструкции для (V)KCCNE series

Бренды по названию

Популярные бренды

FMI (V)KCCNE series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KCCNE series

Отзывы:

Похожие инструкции для (V)KCCNE series

Бренды по названию

Популярные бренды