FMI (V)KCCNE series Скачать руководство пользователя страница 22

Страница: 22 / 40

www.fmiproducts.com

116237-01M

CAUTION: Use only new,

black iron or steel pipe. Inter

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe of

1/2" diameter or greater to allow

proper gas volume to fireplace.

If pipe is too small, undue loss

of volume will occur.

Installation must include an equipment shutoff

valve, union and plugged 1/8" NPT tap. Locate

NPT tap within reach for test gauge hook up.

NPT tap must be upstream from fireplace

(see Figure 31).

IMPORTANT

: Install main gas valve (equip

ment shutoff valve) in an accessible location.

The main gas valve is for turning on or shutting

off the gas to the appliance.

Check your building codes for any special

requirements for locating equipment shutoff

valve to fireplaces.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could

result in clogged fireplace valves.

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

FIREPLACE

INSTALLATION

Continued

We recommend that you install a sediment

trap/drip leg in supply line as shown in Figure

31. Locate sediment trap/drip leg where it is

within reach for cleaning. Install in piping sys

tem between fuel supply and fireplace. Locate

sediment trap/drip leg where trapped matter

is not likely to freeze. A sediment trap traps

moisture and contaminants. This keeps them

from going into fireplace gas controls. If sedi

ment trap/drip leg is not installed or is installed

wrong, fireplace may not run properly.

Figure 31 - Gas Connection

* The equipment shutoff valve may be sup

plied with the appliance or you can purchase

it from your retailer.

CONNECTING FIREPLACE TO GAS

SUPPLY

Installation Items Needed

• 5/16" hex socket wrench or nut-driver
• sealant (resistant to propane/LP gas, not

provided)

1. Open lower louver door panel by gently

pulling forward.

2. Route flexible gas line (provided by in

staller) from equipment shutoff valve to

fireplace. Route flexible gas supply line

through one of the access holes on side

of fireplace.

3. Attach flexible gas line from gas supply to

control valve (see Figure 32, page 23).

4. Check all gas connections for leaks. See

Checking Gas Connections,

page 23.

Figure 30 - External Regulator with Vent

Pointing Down (Propane/LP Only)

Propane/LP

Supply Tank

External

Regulator

With Vent

Pointing

Down

Equipment Shutoff Valve

with 1/8" NPT Tap*

3" Minimum

Approved Flexible

Gas Line

Cap Pipe Tee

Nipple Joint

Sediment Trap/Drip Leg

Natural

- From

Gas Meter (5.5"

W.C. to 10.5" W.C.

Pressure)

Propane/LP

From

External Regulator

(11" W.C. to 14"

W.C. Pressure)

Содержание (V)KCCNE series









































Результаты поиска

Содержание (V)KCCNE series

Отзывы:

Похожие инструкции для (V)KCCNE series

Бренды по названию

Популярные бренды

FMI (V)KCCNE series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KCCNE series

Отзывы:

Похожие инструкции для (V)KCCNE series

Бренды по названию

Популярные бренды