background image

www.fmiproducts.com

109493-01R

2

TaBle oF conTenTs

Safety Information ............................................... 2

Specifications

 ...................................................... 3

Fireplace Installation

............................................ 5

Venting Installation

 .............................................. 7

Optional Gas Line Installation

.............................11

Glass Door Installation

 ...................................... 12

Operation and Maintenance Guidelines

 ............ 13

Technical Service............................................... 14

Replacement Parts

 ............................................ 15

Accessories

 ....................................................... 16

saFeTy

 WARNING: Improper instal

-

lation,  adjustment,  alteration, 

service  or  maintenance  can 

cause injury, property damage or 

loss of life. Refer to this manual 

for assistance or additional in-

formation.  Consult  a  qualified 

installer or local distributor.

IMPORTANT: Check local codes 

before installing this fireplace.

Before beginning the installation of the fireplace, 

read these instructions through completely.
•  This FMI PRODUCTS, LLC fireplace and its 

components are safe when installed accord

-

ing to this installation manual. Unless you 

use FMI PRODUCTS, LLC components, 

which have been designed and tested for 

the fireplace system, you may cause a fire 

hazard.

•  The FMI PRODUCTS, LLC warranty will 

be voided by and FMI PRODUCTS, LLC 

disclaims any responsibility for the following 

actions.
a.  Modification  of  the  fireplace,  com

-

ponents,  doors,  air  inlet  system  and 

damper control.

b.  Use of any component part not manufac

-

tured or approved by FMI PRODUCTS, 

LLC in combination with a FMI PROD

-

UCTS, LLC fireplace system.

Proper installation is the most important step in 

ensuring safe and continuous operation of the 

fireplace. Consult the local building codes as to 

the particular requirements concerned with the 

installation of all factory built fireplaces.

 WARNING: Do not install a 

fireplace insert in this firebox un

-

less the manufacturer's instruc-

tions with the insert specifically 

state  this  fireplace  has  been 

tested for use with the insert.

This fireplace is not intended to 

be used as a substitute for a fur-

nace to heat an entire home. Use 

for supplemental heat only.

FOR YOUR SAFETY

•  Do not store or use gasoline 

or any other flammable vapors 

or liquids in the vicinity of this 

or any other appliance.

•  Due to high temperatures, the 

appliance  should  be  located 

out  of  traffic  and  away  from 

furniture and draperies.

•  Do not place clothing or other 

flammable materials on or near 

the appliance.

•  Never  leave  children  unat

-

tended when a fire is burning 

in the fireplace.

 WARNING: Use solid wood 

or processed solid fuel firelogs 

only.  When  processed  wood 

fuel fire logs are used, do not 

poke or stir the logs while they 

are burning. Use only fire logs 

that  have  been  evaluated  for 

the application in fireplace and 

refer  to  fire  log  warnings  and 

caution markings on packaging 

prior to use.

  WARNING:  Always  leave 

glass  doors  fully  opened  or 

fully  closed  when  operating 

fireplace.

Содержание (V)G42

















Отзывы: