background image

For more information, visit www.fmiproducts.com

SAVE THIS BOOK

This  book  is  valuable.  In  addition  to  instructing  you 

on how to install and maintain your appliance, it also 

contains information that will enable you to obtain re-

placement parts or accessory items when needed. Keep 

it with your other important papers.

This fireplace is approved for use as a wood burning fire

-

place or for use with a vented gas log approved to ANS 

Z21.60 or Z21.84 standards or for use with a vent-free gas 

log heater approved to ANS Z21.11.2 standard.

This wood burning fireplace complies with UL127-CAN/ULS-

S610-M87 standard as a FACTORY BUILT APPLIANCE.

FOR CANADA: The authority having jurisdiction (such 

as the municipal building department, fire department, 

etc.) should be contacted before installation to deter-

mine the need to obtain a permit.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

42" and 50" Wood Burning 

Masonry Fireplace

oWner’s operaTion and 

insTallaTion Manual

(V)g42/50

Smooth Face with Insulation

(V)g42r/50r

Smooth Face with Insulation and 

Bottom Door Rail

(V)g42H/50H

Smooth Face with Insulation and 

Herringbone Refractory

(V)g42Hr/50Hr

Smooth Face with Insulation, Bottom 

Door Rail and Herringbone Refractory

PFS

®

US

C

ICC-ES #ESR-2542

Содержание (V)G42

















Отзывы: