FMI KC42N series Скачать руководство пользователя

Страница: 33 / 44

www.fmiproducts.com

116239-01M

OBSERVED PROBLEM

Pilot lights but flame goes
out when control knob is
released

Burner does not light after
pilot is lit

Delayed ignition burner

Burner backfiring during
combustion

Slight smoke or odor during
initial operation

REMEDY

1. Press in gas control knob

fully

2. After pilot lights, keep gas

control knob pressed in 30
seconds

3. Fully open equipment shut

off valve

4. A) Contact local natural or

propane/LP gas company

B) Clean pilot (see

Clean-

ing and Maintenance,

page 30) or replace pilot
assembly

5. Hand tighten until snug,

then tighten 1/4 turn more

6. Replace pilot assembly
7. Replace control valve

1. Clean burner (see

Clean-

ing and Maintenance

page 30) or replace burner
orifice

2. Contact local propane/LP

or natural gas company

3. Reconnect leads to TP &

TPTH terminals on control
valve

4. Replace thermopile

1. Contact local propane/LP

or natural gas company

2. Clean burner (see

Clean-

ing and Maintenance

page 30) or replace burner
orifice

1. Clean burner (see

Clean-

ing and Maintenance

page 30) or replace burner
orifice

2. Replace damaged burner
3. Replace gas control

1. Problem will stop after a

few hours of operation

TROUbLEShOOTING

Continued

POSSIBLE CAUSE

1. Gas control knob not fully

pressed in

2. Gas control knob not

pressed in long enough

3. Equipment shutoff valve

not fully open

4. Pilot flame not touching

thermocouple, which al

lows thermocouple to cool,
causing pilot flame to go
out. This problem could
be caused by one or both
of the following:

A) Low gas pressure
B) Dirty or partially clogged

pilot

5. Thermocouple connection

loose at control valve

6. Thermocouple damaged
7. Control valve damaged

1. Burner orifice clogged

2. Inlet gas pressure is too

low

3. Thermopile leads discon

nected or improperly con

nected

4. Thermopile is defective

1. Manifold pressure is too

low

2. Burner porting or orifice

clogged

1. Burner orifice is clogged or

damaged

2. Damaged burner
3. Gas regulator defective

1. Residues from manufac

turing processes and logs
curing

Содержание KC42N series













































Результаты поиска

Содержание KC42N series

Отзывы:

Похожие инструкции для KC42N series

Бренды по названию

Популярные бренды

FMI KC42N series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание KC42N series

Отзывы:

Похожие инструкции для KC42N series

Бренды по названию

Популярные бренды