FTr4
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
4. Binding is successful when the receiver's LED stop flashing. Remove the power and bind cables from the receiver.
• If the transmitter is one-way transmission, manually exit the transmitter when the receiver status indicator flashes slowly,
Binding is successful when the receiver's LED stop flashing.
• Remove the bind cables from the receiver, Otherwise when reconnect the power cable to the receiver, it will binding again .Reconnect
the power cable to the model during useing it will causing the model run out of control.
5. Reconnect the power cable to the receiver.
6. Check to make sure that the transmitter and receiver are working as expected, if there are any issues or unexpected operation follow
the steps above to bind again.
对码
Binding
发射机在更新完后，如无法与接收机对码，需强制更新接收机。
1. 用对码线短接 CH4 与 BIND 信号脚 （如右图）；
2. 在发射机端选择接收机更新并进入更新状态；
3. 当接收机指示灯由快闪变为慢闪时表示强制更新成功。
强制更新
Forced update
失控保护
Failsafe
Insert the bind cable
as shown to short the
pins and enter forced
update mode.
注意事项：
• 使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
• 关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将有可能导致遥控设备失控或
者引擎继续工作而引发事故。
• 确保接收机安装在远离电机，电子调速器或电子噪声过多的区域。
• 接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有 1 厘米以
上的距离。
• 准备过程中，请勿连接接收机电源，避免造成不必要的损失。
Attention:
• Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
• Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended
operation or loss of control.
• Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical
noise.
• Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
• Do not power on the receiver during the setup process to prevent loss of control.
If after an update the transmitter is unable to connect or bind to the receiver, it is
necessary to put the receiver into forced update mode
1. Insert the bind cable and CH4 as shown to short the pins and enter forced update
mode. (such as the picture on right)
2. Then go to the RX Setup menu and select RX update as normal.
3. updating is successful when the receiver status indicator flashes slowly.
失控保护功能用于在接收机失去信号不受控制后，接收机按设
置好的失控保护值进行通道输出以保护模型及人员安全。
• 若发射机未设置失控保护通道值输出，接收机在进入失控
保护状态后 PWM、PPM 和 i-bus out 无输出，S.BUS 保持
最后输出；若发射机设置了失控保护，则按照发射机通道
设置值输出。
The failsafe function is used to output the channel according to the
out-of-control protection value after the receiver loses its signal and
is out of control to protect the model and personnel.
• If the transmitter has not set the output of the failsafe channel
value, after the receiver enters the out-of-control state, PWM,
PPM, i-bus will not output, and the S.bus will keep the last
output; if the transmitter is set with the failsafe, follow the
transmitter channel setting value Output.
