background image

General

1. Never allow children or people unfamiliar with these

instructions to use the product.  Local regulations
may restrict the age of the operator.

2. Only use the product in the manner and for the func-

tions described in these instructions.

3. Never operate the product when you are tired, ill or

under the influence of alcohol, drugs or medicine.

4. The operator or user is responsible for accidents or haz-

ards occurring to other people or their property.

Electrical

1. The British Standards Institute recommend the use of a

Residual Current Circuit Device (R.C.D.) with a tripping current
of not more than 30mA.   Even with a R.C.D. installed 100%
safety cannot be guaranteed and safe working practice must be
followed at all times.  Check your R.C.D. every time you use it.

2. Before use, examine cable for damage, replace it if

there are signs of damage or ageing.

3. Do not use the product if the electric cables are damaged or worn
4. Immediately disconnect from the mains electricity supply if

the cable is cut, or the insulation is damaged.  Do not
touch the electric cable until the electrical supply has been
disconnected.  Do not repair a cut or damaged cable.
Replace it with a new one.

5. Your extension cable must be uncoiled, coiled cables can

overheat and reduce the efficiency of your product.

6. Do not pull cable around sharp objects.
7. Always switch off at the mains before disconnecting any

plug, cable connector or extension cable.

8. Switch off before removing or fitting the collection box.
9. Switch off, remove plug from mains and examine electric

supply cable for damage or ageing 

before

winding cable

for storage.  Do not repair a damaged cable, replace it
with a new one.  Use only Flymo replacement cable.

10.Always wind cable carefully, avoiding kinking.
11.Never pull on the cable to disconnect any of the plugs.
12.Use only on AC mains supply voltage shown on the

product rating label.

Preparation

1. Always wear suitable clothing, gloves, and stout shoes.  Avoid

wearing loose-fitting clothing or that has hanging cords or ties.

2. Obtain and wear safety glasses at all times.
3. Before using the machine check that all screws, nuts, bolts

and other fasteners are properly secured and guards and
screens in place and in good working condition.

4. Replace damaged or unreadable warning and oper-

ating labels.

5. Before starting the product, make certain that the feed

inlet is empty.

6. Do not operate the product in the vicinity of

bystanders.

Use

1. Use the product only in daylight or good artificial light.
2. Operate the product only on a firm, level surface.
3. Do not allow hands or any other part of the body or cloth-

ing inside the feed inlet or near any moving part.

4. Keep face and body away from the feed inlet opening.
5. Keep a proper balance and footing at all times.  Do not

overreach.  Never stand at a higher level than the base of
the product when feeding material into it.

6. When feeding material into the product be extremely

careful that pieces of metal, rocks, bottles, cans , ropes,
netting or other foreign objects are not included.

7. When feeding material into the product be extremely

careful that the mains cable is not accidently fed into the
product.

8. Keep hands and feet away from the cutting means at all

times and especially when switching on the motor. 

9. Do not touch the cutting means before the machine

is disconnected from the supply and the cutting
means have come to a complete stop.

10.Do not tilt product when the power source is running.
11. Do not fold product when the power source is running.
12.When folding the product for storage please ensure

the mains cable is kept clear.

13.Whilst using the product ensure the cable does not

become trapped under the wheels or support feet.

14.Do not allow processed material to build up in the dis-

charge area.  This may prevent proper discharge and can
result in kickback of material through the feed opening.

15.Use only Approved Replacement Parts.
16.Remove the plug from the mains :
-

before leaving the product unattended for any period or
when transporting;

-

before clearing a blockage;

-

before checking, cleaning or working on the product;

-

if the product starts to vibrate abnormally or makes an
unusual noise.  Check immediately.  Excessive vibration
can cause injury.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure the

product is in safe working condition.  Do not attempt to
repair the product unless you are competent to do so.

2. Check the collection box frequently for wear or deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement parts specified for this product.
5. Be careful during folding of the product to prevent

entrapment of the fingers between moving and fixed
parts of the machine.

IMPORTANT

Use only 1.5mm

2  

size cable up to 25 metres length maximum.

Maximum rating :

1.5mm

2  

size cable, 16 amps 250 volts AC.

YOUR PRODUCT IS SUPPLIED WITH CABLE
WIRED DIRECTLY INTO THE PRODUCT.

1.Do not wire an extension cable directly to your product your-

self.  Please contact your local Approved Service Centre for
further information on the connectors and kits available.

2.Only use extension cables specifically designed for outdoor use.
3.Only use 1.5mm

3 core extension cable.

MAINS PLUG REPLACEMENT
• If the plug supplied is cut off it should be destroyed.

There is an electric shock hazard if a cut off plug is
inserted into a 13 amp socket.

1.

Ensure the mains voltage suits your product

2.

IMPORTANT!  

The wires in the mains lead are

coloured in accordance with the following code:

BLUE - NEUTRAL BROWN - LIVE   GREEN/YEL-
LOW - EARTH
The wire which is coloured BLUE must be connected
to the Terminal which is marked with the letter 'N' or
coloured BLACK.  The wire which is coloured
BROWN must be connected to the Terminal which is
marked with the letter 'L' or coloured RED.  The wire
which is coloured GREEN/YELLOW must be connect-
ed to the Terminal which is marked with the ‘earth’
symbol.

4.It is important that the outer sheath is clamped cor-

rectly into the 3-pin plug. 

5.If in doubt consult your local Service Repairer or quali-

fied electrician before the machine is used.  

6.

A 13 Amp fuse must be fitted to the Mains Plug.   

7.The normal plug fuse and household fuse only protect

the electrical equipment and are not a safeguard
against electrocution.

Cable Information

Содержание Pac a Shredder










Отзывы: