this case, do not tilt it more than absolutely necessary
and lift only the part, which is away from the operator.
13. Do not start the machine when standing in front of
the discharge opening.
14. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
15. Do not transport the machine while the power source
is running.
16. Stop the machine, and remove the plug from the
socket. Make sure that all moving parts have come
to a complete stop
• whenever you leave the machine,
• before clearing blockages or unclogging chute,
• before checking, cleaning or working on the
machine,
• after striking a foreign object. Inspect the machine
for damage and make repairs before restarting and
operating the machine;
if the machine starts to vibrate abnormally
(check immediately)
• inspect for damage,
• replace or repair any damaged parts,
• check for and tighten any loose parts.
Maintenance and storage
1. Keep all nuts, bolts, and screws tight to be sure the
machine is in safe working condition.
2. Check the grass collector frequently for wear or
deterioration.
3. On machines with multi blade, take care as rotating
one blade can cause other blades rotate.
4. Be careful during adjustment of the machine to pre-
vent entrapment of the fingers between moving blades
and fixed parts of the machine.
5. Always allow the machine to cool down before storing.
6. When servicing the blades be aware that, even though
the power source is switched off, the blades can still
be moved.
7. Replace worn or damaged parts for safety. Use only
genuine replacement parts and accessories.
Additional safety instructions
Electrical safety
WARNING! Cardiac arrest!
This product makes an electromagnetic field while
it operates. This field may under some conditions
interfere with active or passive medical implants.
To decrease the risk of conditions that can possibly
injure or kill, we recommend persons with medical
implants to speak with their physician and the medi-
cal implant manufacturer before you operate the
product.
Before use, examine the cable for signs of damage or
ageing. If the cable is found to be defective, take the
product to an Authorised Service Centre and have the
cable replaced.
Do not use the product if the electric cables are damaged
or worn.
Immediately disconnect from the mains if the cable is cut,
or the insulation is damaged. Do not touch the electric
cable until the cable has been disconnected. Do not
repair a cut or damaged cable. Replace it with a new one.
The extension cable must be uncoiled. Coiled cables can
overheat and reduce the efficiency of your mower.
Keep the extension cable away from product, always
work away from the power point mowing up and down,
never in circles.
Do not pull cable around sharp objects.
Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
Stop the engine, disconnect the mains and examine the
cable for damage or ageing before you wind the cable for
storage. Do not repair a damaged cable, replace it with
a new one. Use only genuine replacement cable.
Always wind the cable carefully, avoid kinking.
Do not carry the product by the cable.
Do not pull on the cable to disconnect any of the plugs.
Use only on AC mains supply voltage shown on the
product rating label.
Our products are double insulated to EN60335. Do not
connect an earth to any part of the product.
Check the working area for hidden cables.
Do not use for pond care or close to water.
Personal safety
WARNING! Risk of suffocation!
Small parts can be easily swallowed. There is also
a risk that the polybag can suffocate toddlers. Keep
toddlers away when you assemble the product.
Do not use in explosive atmosphere.
Do not operate the product when you are tired, ill or
under the influence of alcohol, drugs or medicine or you
exhausted.
Do not overload the mower.
Use gloves, wear slip resistant shoes and wear eye pro-
tection.
Do not use under wet conditions.
Do not use on wet grass.
Do not disassemble the product further than the delivery
status.
Only start the mower with an upright standed handle.
Do not use the start levers alternately.
Use the handles carefully.
Safety Cut-Out
The engine is protected by a Safety Cut-Out which is acti-
vated when the blade becomes jammed or if the engine is
overloaded. When this occurs, stop and disconnect the
product from the mains. The Safety Cut-Out will only reset
when you release the start/stop lever. Clear any obstruc-
tion and wait for a few minutes for the Safety Cut-Out to
reset before you continue to use the product.
4
