background image

Installation and maintenance manual for mechanical fuel pump FLYGAS – Version 1.2 Experimenter 

 

WARNING ! 

 

This Manual is an integral part of  your  kit and shall be kept with it for 
future reference. 
Retain this Manual in a suitable place and when consulting it, take care 
of not spoiling it. 
Should your kit be resold, entrust it to the new owner who will obviously 
need the information contained. 
This Manual consists in 24 pages including cover.

 

 

 
 
 
 

 
 
 
 

 

 

 

RIGHT OF WITHDRAWAL

 

 

The buyer has the right to withdraw from the purchase of this kit if within 10 
days  of  purchase,  after  received  this  kit,  considers  the  unsuitability  of  their 
vehicle to receive the installation of this system. 
In  this  case  Flygas  reserves  to  repay  the  full  amount  paid  (equal  to  the 
invoice) and collect all the material, as long as it is intact in all its parts, not 
altered  or  defaced  and  stored  under  appropriate  conditions, without  charge 
or duty by the purchaser. 
The material should be delivered free at the headquarters Flygas. 

 

Insurance 

 
No insurance is included in the purchase of our kit. 
Please,  note  that  the  installation  of  our  Mechanical  Fuel  Pump  kit  could  be 
change  the  basic  characteristics  of  the  engine  and  of  the  vehicle.  It’s  so 
necessary to review the insurance contract verifying insurance coverage and, 
in  case,  examine  the  possibility  of  creating  a  new  insurance  policy  that 
permits such changes. 
In case of accident or in case of damages caused to property or third persons, 
Flygas will not be liable in any way.

 

Содержание F.050

























Отзывы: