background image

 

23 

11.

 

MAINTENANCE SYSTEM 

 

A  proper  and  regular  maintenance  is  of  essential  importance  for  the  durability  of  the  mechanical 
parts of the kit. 

 

 

In  addition  to  the  routine  maintenance  that  may  be  performed  with  all  the 
necessary precautions, even by unskilled persons, you should contact a qualified 
technician  for  special  maintenance  and  repair  of  delicate  components  or  whose 
reassembly requires special tools. 

 

 

 

 

Every 50 hours  

 

Every  50  hours

  of  use  it  is  necessary  to  clean  the 

fuel  filter  Gascoletor

  to  prevent  that  dirty 

particles can completely occlude the filter and  thus the passage of gasoline. 

 

In  case  you  should  realize  that  you  have  used  polluted  fuel  clean  and  wash  

immediately

  the  entire  plant  (  independently  of    the  flight  hours).  The  same 

security  measures  must  be  taken  whenever  you  perform  works  in  which  dirt 
inside  the  fuel  plant  may  enter  (ex.  during  the  installation  of  the  kit  or  during 
works on the tanks). 

 

Every 250 hours 

 

Every  250  hours  of  use  make  all  the  scheduled  maintenance  checks  indicated  by  the  engine 
manufacturer including the above mentioned descriptions. 
Jut for this test, keep switch off electrical fuel pump, and check fuel pressure in function of Rpm in 
your installation, and fill the table below: 
 

 

 
Every  250  hours  or  anyway  every  year,  chec

k  the  conditions  of  spring  and  ball  of  the  “By-Pass 

Valve”, corrosion could be damage its. 
 

 

 

Every 1500 hours  

 

 

Replace Mechanical Fuel Pump

 

 
After 1500 hours of use send the mechanical fuel pump  to the Flygas he will arrange its revision 
and  the replacement of the worn parts.

 

 

   

        Performance Test of Mechanical Fuel Pump installed on your engine

 Pressure and Flow Liters by hour

Just Installed

After 250Hours

After 500Hours

After 750Hours

After 1.000Hours After 1.250Hours After 1.500Hours

Data:__________ Data:__________ Data:__________ Data:__________ Data:__________ Data:__________ Data:__________

RPM

Fuel Temp: _____ Fuel Temp: _____ Fuel Temp: _____ Fuel Temp: _____ Fuel Temp: _____ Fuel Temp: _____ Fuel Temp: _____

2000
3000
4000
5000

Содержание F.050

























Отзывы: